Manuals
/
Fujitsu
/
Computer Equipment
/
Server
Fujitsu
B120 manual
Models:
B120
1
46
68
68
Download
68 pages
12.34 Kb
43
44
45
46
47
48
49
50
<
>
Troubleshooting
Install
Error codes
Replacement of SCSI hard disk drive during operation
Warranty
Configuring the server
Instructions on connecting and disconnecting cables
any technical problems or other questions you need clarified?
Diagnostic System
Setting up the tower server
Page 46
Image 46
Page 45
Page 47
Page 46
Image 46
Page 45
Page 47
Contents
Intel-based Server Systems
PRIMERGY B120
OPERATING MANUAL
Are there
any technical problems or other questions you need clarified?
Please contact one of our service partners your sales partner
your sales outlet
Page
A26361-K646-Z102-1-7619
Introduction Important notes Installation
PRIMERGY B120
Operating Manual
Property and data protection Troubleshooting and tips
Offenders will be liable for damages
Pentium is a registered trademark of Intel Corporation, USA
Copyright ã Fujitsu Siemens Computers GmbH
This manual was produced by
3 Installation
Contents
Contents
9 Index
System board
1.1 Features
1 Introduction
Hard disk subsystem
Service and Support
Features
Power supply
Introduction
1.2 Notational conventions
Technical data
Electrical data standard power supply
Notational conventions
Mechanical data
Technical data
Standards
Environmental conditions
2 Important notes
2.1 Safety
Installation and operation
Before operating the device
Important notes
Safety
Poper operation of the system, warranty features
Batteries
Modules with electrostatic sensitive components
2.2 CE certificate
CE certificate
Other important notes
2.4 Transporting the server
2.3 FCC Class B Compliance Statement
Important notes
Environmentally friendly product design and development
2.5 Disposal and recycling
Disposal and recycling
Note on saving energy
Page
3.1 Installation steps
3 Installation
3.2 Unpacking the server
Installation
3.3 Instructions on connecting and disconnecting cables
3.4 Setting up the tower server
Connecting cables
100 V - 125
3.4.1 Connecting the tower server to the line voltage
Setting up the tower server
200 V - 240
3.4.2 Connecting the monitor to the line voltage
3.5 Installing rack-server in/removing from rack
Installation
3.5.1 Mounting the slide-in module
Installing rack-server in/removing from rack
Installation
Ê Push the server up to the front panel
Installation
Installing rack-server in/removing from rack
A26361-K646-Z102-1-7619
Installing rack-server in/removing from rack
3.5.2 Installing the slide-in module
Fitting spring nuts
Installation
Mounting cage nuts
Installation
Installation
3.5.3 Connecting the rack server to the line voltage
Installing rack-server in/removing from rack
100 V - 125
Prepare the keyboard
3.6 Prepare the keyboard
Installation
Installation
3.7 Connecting devices to the server
Connecting devices to the server
Tower
Installation
4 Preparation for use and operation
Enabling access to the accessible drives
4.1 Unlocking/locking the tower server
Preparation for use and operation
Enabling access to the hard disk drives
A26361-K646-Z102-1-7619
Preparation for use and operation
4.2 Operation controls
Operation controls
A26361-K646-Z102-1-7619
ON/OFF switch
4.2.2 Indicators
4.2.3 Drive indicators
Power-on indicator
Preparation for use and operation
4.3 Switching the server on and off
Switching the server on and off
monitor screen
Server is switched on
Switching the server on and off
Server is switched off
Other switch-on methods
4.4.2 Configuration without ServerStart
4.4 Configuring the server
4.4.1 Configuration with ServerStart
4.4.3 Installing the operating system
Preparation for use and operation
4.5 Locking the tower server
Fitting the hard disk cover
A26361-K646-Z102-1-7619
Locking the server
4.6 Cleaning the server
Cleaning the server
Preparation for use and operation
Page
5 Opening and closing the server
5.1 Opening and closing the tower server
5.2 Opening and closing the rack server
Opening and closing the server
Opening and closing the server
Opening and closing the rack server
A26361-K646-Z102-1-7619
Page
6 Property and data protection
Page
7.2 The server switches itself off
7 Troubleshooting and tips
7.1 Operation indicator remains dark
Power cord incorrectly connected
7.4 Flickering stripes on the monitor screen
Troubleshooting and tips
Power cable or monitor cable not connected
7.5 No screen display or display drifts
SCSI configuration incorrect standard SCSI controller
7.9 System does not boot
Mouse controller disabled
7.6 No mouse pointer displayed on the screen
The Disk Array Controller configuration is incorrect
7.10 Drives dead at system boot
7.12 Error messages on the screen
Disk Array Controller is not configured for this hard disk drive
8 System components and expansions
8.1 The SCSI hard disk subsystem
RAID level 0 and
8.1.1 SCSI hard disk drives
System components and expansions
RAID level 1 and 5 without standby hard disk
Orange indicator
8.1.2 Replacement of SCSI hard disk drive during operation
Function of the indicators Green indicator
The SCSI hard disk subsystem
8.1.3 Installing/removing a SCSI hard disk drive
System components and expansions
The SCSI hard disk subsystem
8.1.4 SCSI platter for four 1-inch hard disk slide-in modules
System components and expansions
SCSI drive
8.2 Accessible drives
IDE drive
System components and expansions
Accessible drives
8.2.1 Installing/Removing an accessible 5 ¼-inch drive
System components and expansions
8.2.2 Changing the floppy disk drive
System components and expansions
Removing/installing boards
8.3 Removing/installing boards
System components and expansions
8.4 chipDISK for RemoteView
8.4.1 Installing/removing the chipDISK
System components and expansions
chipDISK for RemoteView
8.4.2 Configuring the chipDISK
Diagnostic System
System components and expansions
8.5 Replacing the system fan
System components and expansions
Adapter module
8.6 Adapter module
8.7 System board
System components and expansions
Page
9 Index
Index
K Keyboard
Index
Index