Manuals / Fujitsu / Computer Equipment / Server

Fujitsu RX200 manual Controllers in Non-Hot-Plug PCI Slots, V Caution

Models: RX200

1 68

Download 68 pages 59.47 Kb

Page 47

Image 47

8Controllers in Non-Hot-Plug PCI Slots

VCAUTION!

Please observe the safety information in the chapter “Safety Instructions” on page 9ff.

If you want to replace components which are not hot-pluggable, you must proceed as follows:

ÊShut down the operating system

ÊSwitch off the server, and

ÊUnplug the power plugs.

The system board contains two PCI-X slots, which can only be used via a riser card because of the height of the server:

–PCI-X slot 1: 64 bit/133 MHz, max. length 315 mm

–PCI-X slot 2: 64 bit/66 MHz, low profile, max. length 175 mm

IBoth slots are not hot-pluggable.

OptionsGuide

Page 47

Image 47

Fujitsu RX200 manual Controllers in Non-Hot-Plug PCI Slots, V Caution

Contents

Options Guide PRIMERGY RX200 S2 ServersystemCertified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Copyright and Trademarks Continued Preface Procedure Safety Instructions Preparation Main MemoryProcessors Accessible Drives Controllers in Non-Hot-Plug PCI Slots RemoteView Components CompletionPage Abbreviations Related publications Index Page Related publications ContentsControllers in Non-Hot-Plug PCI Slots AbbreviationsPage ServerBooks CD supplied 1 Preface1.1 Overview of the documentation ServerBooks CD suppliedServerBooks CD supplied Reklamat-PC-LOG@fujitsu-siemens.comOverview of the documentation PrefaceExtensions and conversions 1.2 Extensions and conversionsAdditional controllers in non-hot-plug PCI slots RemoteView Service Board S2 LPExtensions and conversions PrefaceItalics 1.3 Notational conventionsPage V CAUTION 2 ProcedurePage V CAUTION 3 Safety InstructionsBefore setting up V CAUTION Installation and operation V CAUTION V CAUTION Notes on handling CDs in CD-ROM/DVD drives V CAUTION Batteries V CAUTIONFigure 1 ESD label Place all components on a static-free base Safety InstructionsDo not touch any exposed pins or conductors on a component V CAUTIONFigure 2 Removing the server 4 Preparation4.1 Opening the server Figure 3 Removing the cover Preparation5 Main Memory 5.1 Installation rulesUpgrading / exchanging main memory 5.2 Upgrading / exchanging main memory6 Processors 6.1 Installing a second processorFigure 6 Removal of the ventilation duct Installing a second processorRemoving the ventilation duct ProcessorsRemoving the heat sink dummy Installing the processorInstalling a second processor ProcessorsVCAUTION Installing a second processorProcessors Installing the heat sinkInstalling the ventilation duct Figure 10 Installing the heat sinkV CAUTION 6.2 Exchanging the processorExchanging the processor Figure 12 Removing the old processor Figure 13 Installing the new processorExchanging the processor Exchanging the processor Exchanging the heat sink 6.3 Exchanging the heat sinkPage V CAUTION 7 Accessible DrivesInstalling the LocalView Module 7.1 Installing the LocalView ModuleFigure 15 Connecting the LocalView module Installing the LocalView ModuleAccessible Drives 7.2 Installing a CD-ROM/DVD driveFigure 17 Mounting the drive in its frame Installing a CD-ROM/DVD driveFigure 18 Installing the CD-ROM/DVD drive Installing a CD-ROM/DVD driveInstalling a floppy disk drive 7.3 Installing a floppy disk driveFigure 20 Mounting the drive in its frame Installing a floppy disk driveRemoving/installing a floppy disk drive Figure 21 Connecting the data cable Accessible DrivesPage V CAUTION 8 Controllers in Non-Hot-Plug PCI SlotsRemoving the riser card holder 8.1 Installing controllersInstalling controllers Installing a PCI boardInstalling controllers Reinstalling the riser card holderPage 9 RemoteView Components 9.1 Installing the RemoteView Service Board S2 LPFigure 24 Installing the RSB S2 LP Installing the RemoteView Service Board S2 LP RemoteView Components10.1 Closing the server 10 CompletionCompletion Figure 26 Installing the serverClosing the server Abbreviations Abbreviations Abbreviations GAM Abbreviations Abbreviations RTDS Page Related publications 16 Integrated Mirroring User’s Guide Index Index riser card holder installation 41 removalU upgrade ventilation duct installation 23 removalSubmitted by Comments on PRIMERGY RX200 S2 Serversystem Comments Suggestions CorrectionsFujitsu Siemens Computers GmbH User Documentation 33094 Paderborn GermanyPage Submitted by Comments on PRIMERGY RX200 S2 Serversystem Comments Suggestions CorrectionsFujitsu Siemens Computers GmbH User Documentation 33094 Paderborn Germany