Aux Audio | Garmin 225B, 225A specs

3.3.2Aux Audio

The Aux function allows you to turn Aux Audio On/Off and set the volume value.

1.Press FUNC to access the Functions. Turn the LARGE knob to select the ICS Function. Turn the SMALL knob to view the Aux Volume function. Then, press the ENT key.

Figure 3-17 Select the Aux Audio Function

2.Turn the SMALL knob to turn the Aux Audio On or Off.

3.Turn the LARGE knob to select the Aux Volume. Turn the SMALL knob to set the value. Then, press the ENT key.

Turn Small Knob To Turn Aux On/Off

Turn LARGE And

Then SMALL Knob To

Adjust Aux Volume

Press the ENT Key to Save the Displayed Value

Press the CLR Key To Revert to the Previous Value

Figure 3-18 Adjust the Aux Audio

4.Press the CLR key to revert to the previous Volume value and then repeat step 3 to select a new value.

3-10

Garmin GTR 225/225A/225B Pilot’s Guide

190-01182-00 Rev. A

Page 28

Image 28

Garmin 225B, 225A manual Turn the Small knob to turn the Aux Audio On or Off

Contents

GTR 225/225A/225B November Limited Warranty Garmin GTR 225/225A/225B Pilot’s Guide Operation Product Registration and Support US Toll Free Canada Toll Free Contents Index Index-1 Product Description Photo Sensor Power/Com Volume/Squelch Knob Pilot Controls Tuning LARGE/SMALL Concentric Cursor Knobs FLIP/FLOP KeyCom Key MEM Key Func Function Key USB PortMON Monitor Key Power On Com RadioSelecting a Com Frequency Selected Frequency Monitoring the Standby Com Channel Saving a Com ChannelAfter selecting the desired characters, press ENT Monitor Annunciation Standby Frequency Being Monitored After making a selection, press ENT Selected Wpt Type Emergency Channel Com Database Look-UpActive and Standby frequencies Stuck Mic Frequency Database Reverse Look-UpRemote Frequency Selection Control Airport Identifier Shown For Freqs In Database This page intentionally left blank SYS Config Com Spacing Functions Description Com Frequencies Press the Func key to access the FunctionsRecent Com Frequencies Com User Frequencies Press the CLR key to delete this User frequencySelected Frequency Select Wpt Name Select Wpt Type Press ENT Key To Delete Selected Freq Frequencies. Press ENT Select User FreqsSelect User Freq Value Select User Wpt Name Com Database Frequencies Press ENT Key To Set Selected Freq As StandbyIdentifier Selected Freq As Active Com Nearest Airports APT Com Nearest Area Control Center ACC FrequenciesTurn the Small knob to display the available ACCs Turn Small Knob To Scroll Through Available Airports Com Nearest Flight Service Station FSS Frequencies 13 Com Nearest FSS Frequencies Com Nearest Weather WX Frequencies 14 Com Nearest Weather Frequencies ICS Configuration Adjust Intercom Aux Audio Turn the Small knob to turn the Aux Audio On or Off Intercom On/Off Speaker On/OffIntercom On/Off function. Then, press the ENT key Speaker On/Off function. Then, press ENT Com Spacing System ConfigurationTurn the Small Knob to Select the Channel Spacing Brightness Display BrightnessSelect the Offset Value Display Contrast Database InfoDisplay Contrast function. Then, press the ENT key Database Version function. Then, press the ENT key Load Database function. Then, press the ENT key Load DatabaseUSB Port USB Cable USB Memory Device Software Version Serial NumberPress the Func key to return to the main menu Serial Number function. Then, press ENT Timers Setting Up the Count Down Timer Setting Up the Count Up Timer Viewing Timers in the Com DisplayPressing CLR and then ENT will reset the displayed Timer Pressing ENT twice will stop the displayed Timer Count Down Timer Value Highlighted When Counting Up 36 Count Down Timer Value Now Counting Up This page intentionally left blank Troubleshooting Appendix It can be enabled Or disabled via a Remote mountedIf in Lock Out mode Check Mic key input Updating the Frequency Database Messages Power has been Re-apply power to the unit Switch has beenAll installations Radio will no longer Transmit Installations This input will now Index Stuck mic 2-5 Support