6K8-Series Port Module 6KPMV Installation | GarrettCom instruction

Magnum 6K8-Series Industrial Field Switch

Installation and User Guide (04/07)

3.66K8-Series Port Module (6KPMV) Installation

Note: The modules used in the 6K8-Series vertical mount unit are similar to

those used in 6K16V units. The modules have the letter “V” in the model numbers, to order the right module for this unit. In the Port Module materials below, all modules are referred to as “6KPMV” for convenience in describing port module installation.

Magnum 6K8-Series Switches are normally received from the factory with all required 6KPMV modules installed. There may be situations where 6KPMV cards need to be added or replaced. In cases where additional 6KPMV cards are needed, the faceplate for an available front-mounted slot must be removed. The following procedure describes this operation. The pictorial view of the hardware assembly can be seen here-

http://www.garrettcom.com/Pictorial/6k8_pictorial.pdf

3.6.1 Preparation for Installing and Removing 6KPMVs from 6K8’s

STOP!!!

Be sure the power cord is unplugged

from the chassis before attempting to remove

and/or replace any PM cards.

Failure to do so may result in damage to the unit

and will void the warranty.

Caution- Opening of the 6K8 chassis can only be performed by trained service

persons. Avoid Static Discharge: The port modules (like most electronic equipment) are sensitive to static discharge. Use proper ESD measures when handling port modules.

Step 1. Make sure the 6KPMV Card package has all necessary accessories and use the proper tool to install it properly. Each 6KPMV Card package, for field installation contains (Daughterboard (Bigger) and Granddaughter board (smaller), three 5/8 stand offs for Granddaughter board, 6 standoff for daughter Board, nine #4-40x3/8 Pan-Head screws along with Front panel face plate package.

NOTE: Every 6KPMV Card package comes with their matching Daughter and Granddaughter board. The copper 6KPMV card should not work properly if mixed with other Fiber combo 6KPMV card packages. Always install the PM module separately one by one to avoid the mixing.

Do not change the Blue color DIP Switch setting ever! Leave it at factory default.

www . GarrettCom . com

36

Image 41

GarrettCom manual 6K8-Series Port Module 6KPMV Installation, Preparation for Installing and Removing 6KPMVs from 6K8’s

Contents

Industrial Field Switch Trademarks Canadian Emission Contacting GarrettCom, Inc Introduction Table of ContentsInstallation 14 6KM-BLNK Troubleshooting Overview Magnum Line Performance Technical SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment Lengths Fiber Single-mode connector types Fiber Multi-mode connector types supportedAlarm Relay Contacts Management Console connector Per-port MDI or Mdix on RJ-45 DC Power Supply OptionsMountings Agency Approvals Magnum 6K8 Magnum 6K8 Port Modules Configuration OptionsOrdering Information GBIC1000Mb Transceiver options for Mangum 6K8-Series Introduction Inspecting the Package and Product Product Description Magnum 6K8-Series 6K8 1a Magnum 6K8-Series, Industrial Field Switch Www . GarrettCom . com Operate in full-duplex mode for best Normally are set factory default toFiber distance and performance. Using Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb Fiber Speed when on and at 10 MB When lit. The 10/100 LED Indicates operation at 100MbSpeed when OFF when auto Negotiation is not disabled FDX/HDX LED is on to ST or SC @RJ-45 + 2@ 100Mb Four-Port 10 MB and 100Mb mm Fiber ST Modules Gigabit 1000Mbps port modules 7a GBPM-2OTX Two Gigabit port option Packet Prioritization, 802.1p QOS Gbic Description Managed Network Software MNS-6K for Magnum 6K8-Series Frame Buffering and Flow Control Www . GarrettCom . com „ Large selection of built-in fiber options at 10/100/1000Mb Applications Interne Control Center Scada Mounting Instructions Connecting Ethernet Media Locating Magnum 6K8-Series SwitchesIeee Standard Media Type Max. Distance Port Module Fiber Copper Connecting Single-Mode Fiber Optic Connecting Fiber Optic ST-type, twist-lockConnecting Fiber Optic SC-type, Snap-In 100BASE-TX Media Ieee Standard Www . GarrettCom . com DIN-Rail Mounting Quantity Description Din-Rail kit Installation procedures Www . GarrettCom . com Mounting Dimensions for 6K8 with metal brackets Powering the Magnum 6K8-Series Industrial Field Switch Www . GarrettCom . com Preparation for Installing and Removing 6KPMVs from 6K8’s 6K8-Series Port Module 6KPMV Installation 1a Removing the Top panel from the Chassis base of the unit Remove Chassis Cover 2b Granddaughter Board shown separately Installing 6KPM Cards in the Magnum 6K8-Series2a a Magnum 6K8 unit with main board motherboard only Female latch connector 2h sliding in the top cover onto the chassis base track Removing a 6KPM Card Removing 6KPM CardsRetaining screws shown by arrows Remove 6KPM Card Enlarged view of Magnum 6K8-Series Console Port area Connecting a Management Console Terminal to Magnum 6K8 1 RS-232 DB-9 Console Com port Serial port pin assignments Switching FunctionalityDB-9 Console port connector Address Learning Dual LEDs Status on TOP and Front of the 6K8-Series unitFiltering and Forwarding Auto-Cross Mdix and Auto-negotiation, for RJ-45 ports Flow-control, Ieee 802.3x Standard Www . GarrettCom . com ’cvr 6KP4V 6KPMV Module Description Introduction Magnum 6K8 Industrial Field Switch Port Modules Switch, the copper port Segments. When installed in aDual speed copper ports Magnum 6K8-Series Managed 1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Magnum 6KP6 Mode 100Mbps fiber opticTransceivers all in one module. This Activity ACT, Link LK, 10/100Mbps RJ-45 Ports 2@100Mbps single Mode FX-SC-type, snap Connector6KP6-RJSSC 4@ Port@ 100Mbps Multi-Mode Fiber port 5 6KP8-MTRJ, 8 @100Mb multi-mode FX, Mtrj Small-Form-factor Magnum 6KP8-45MT Module is a combo module with Port multi-mode fiber LC connector 10/100Mb 8-Port 9 6KP8-RJ45 Twisted Pair PoE LEDs Summary 45-2MT eight ports Module is a 12a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector GBIC-SXSC Gigabit fiber 1000Mb, multi-mode SC ConnectorStandard 1@ 1000Mb Fiber SC + 2@ 100Mb SC GBPM-2OTX Two Gigabit option Before Calling for Assistance When Calling for Assistance No Problem Found Appendix B Internal DC Power Supply Options B3.0 Applications for DC Powered Ethernet Switches B2.0 -48VDC, 24VDC and 125VDC POWER, Theory of Operation B4.0 6K8-SERIES, -48V, 24, 125 or 5VDC Installation B7.0 Troubleshooting C4.0 Features and Benefits of the DUAL-SOURCE Design C5.1 UL Requirements External Terminal Block on a Magnum 6K8 -48VDC Example Magnum 6K8 -24VDC C6.0 Ordering Information Optional