Replacing the Backup Battery
¾To replace the backup battery:
1.Turn the ON/OFF switch on the back of the panel to OFF.
2.Remove the panel cover by lifting on the tab at the top of the panel.
3.Loosen the speak screws. This makes removing the battery easier.
4.Remove the battery cover screw and cover. (See Figure 3)
Battery Cover | Cover Screw | Backup Battery |
|
|
Speaker Screws
Slide cover off to the right
I N S T R U C T I O N S
Add Option
Option #1: Panel Voice Enable | START MENU | |||
Option #2: Account No. |
|
| ||
Option #3: Phone No. | Clock Set |
| ||
|
| See Note |
| 1 |
Press |
| and |
| |
|
|
| ||
| Add | Option # |
|
|
voice prompts. |
|
|
| |
Add Access |
| Add | 2 | |
See Note |
| |||
|
|
|
| |
Press |
| , then |
|
|
| Add Access Code DONE |
|
| |
use | numbers to enter access code. |
| 3 | |
|
|
|
| |
Clock |
| Delete |
| |
|
| See Note |
| |
Press |
|
|
| 4 |
| Clock Set | Hours Minutes DONE |
| Access Code |
Delete |
|
|
| |
To delete an option or access code |
| 5 | ||
press | and follow voice prompts. | Test | *Sensor | |
| Delete |
|
|
|
Cancel |
| MAIN MENU | *Option # | |
If you make a mistake or want to start |
| |||
over press | * Press for program information. | |||
| Cancel | |||
+
| 6 |
Hours | + |
-Minutes
7
-
8
DONE
9
Cancel
0
Note:
Hold key or press repeatedly until you hear the desired item.
I N S T R U C T I O N S
Add Option
Option #1: Panel Voice Enable | START MENU | |||
Option #2: Account No. |
|
| ||
Option #3: Phone No. | Clock Set |
| ||
|
| See Note |
| 1 |
Press |
| and follow |
| |
|
|
| ||
| Add | Option # |
|
|
voice prompts. |
|
|
| |
Add Access Code | Add | 2 | ||
| ||||
|
| See Note |
|
|
Press |
| , then |
|
|
| Add Access Code DONE |
|
| |
use red numbers to enter access code. |
| 3 | ||
|
|
|
| |
Set Clock |
| Delete |
| |
|
| See Note |
| |
Press |
|
|
| 4 |
Clock Set | Hours Minutes DONE |
| Access Code | |
Delete |
|
|
|
|
To delete an option or access code |
| 5 | ||
press | and follow voice prompts. | Test | *Sensor | |
Delete |
|
|
| |
Cancel |
|
| MAIN MENU | *Option # |
If you make a mistake or want to start |
| |||
over press |
| * Press for program information. | ||
| Cancel | |||
+
| 6 |
Hours | + |
-Minutes
7
-
8
DONE
9
Cancel
0
Note:
Hold key or press repeatedly until you hear the desired item.
Note
Lifting the panel and tilting it toward yourself should aid in the removal of the battery.
Note
If Status is pressed during a sensor low battery, the sys- tem announces “Time is x:xx, sensor X panic, low battery” and the panel will stop beeping for 4 hours.
Figure 5. Replacing the backup battery
5.Remove the old battery.
6.Disconnect the cables from the old battery and connect them to the new one.
7.Install the new battery, positioning it under the edge of the speaker.
8.Carefully place the connecting wires above the speaker.
9.Tighten the speaker screws.
10.Replace the battery cover.
11.Replace and tighten the cover screw.
12.Replace the panel cover.
Sensor Low Battery
¾If the panel gets a low battery message from a sensor, the following occurs:
1. The panel sends a Sensor Low Battery report to the central station.
2. The Status light turns on.
3. If Option 25: Trouble Beeps is enabled, six trouble beeps will sound once a minute.
When the low battery condition is fixed, the panel stops the trouble beeps and turns off the Status light. See the sensor manual for information on replacing its battery.
Sensor Supervisory Failure
¾If the panel does not hear from a sensor within the programmed RF Timeout (Option 15) the following occurs:
1.The panel sends a Sensor Supervisory Failure report to the central station.
2.The Status light turns on.
3.If Option 25: Trouble Beeps is enabled, six trouble beeps will sound once a minute.
System Monitoring | 24 |
