GE JMS02PN, JGAS02EN, JGAS02PN manual ~A~~~N~~O&~=A ~ to, Do not USE AN -NSION Cord m ~S Appwce

❑COHNE~ THE M6E ~6~

1.Hthe range is to be connected to house piping with flexible or semi-rigid meti appfiance connector, connector nuts MU= NOT be

connected direc~ to pipe threads.

2.me apphance connector must be instied by using the proper flare union adaptors with the connector. Cutoff valve, appfiance connector and adaptors are not suppfied with the range. Gecause sofid pipe restricts moving the range, we recommend use of AGA certified flexible tubing.) h Canada, flexible connectors must be single wdl meti connectors no longer than 6 feet in length.

c The house piping and connector used to connect the range to the main gas supply must be clean, free of meti shatigs, ruse dirt or fiquids (oH or water). Contaminants in the supply bes can work their way into the range manifold and ause failure of gas valves or controls and clog burners or pflot orifices.

m @ ~@ *fiB

House Flare NM Appliance Nut Flare Range Pressure

Piping Union tinn-orUnion Reguktor

AdapterAdapter

3.hsti a manual shutoff valve in the gas he in an easily accessible location outside of the range. Be sure you know how and whereto shut off the gas supply to the range.

4.Check for leaks. After connecting the range to gas, check the system for leaks with a fiquid leak detector at d joints and connections.

5.Tighten dl connections as necessary to prevent gas leakage in the range or supply he.

~A~~~N~~O&~=A ~ TO

6.Check @ent of valves after connecting the range to the gas supply to be sure the manifold pipe has not been moved. A mistignrnent could cause the valve knob stem to rub on the control panel, resulting in a gas leak at the valve.

Disconnect the range and its individud shut-off valve from the gas supply piping system during any pressure testing of the system attest

pressures greater than 1/2 psig.

Isolate the range from the gas supply piping system by closing its individud manual shut+ff valve during any pressure testing of the gas supply piping system attest pressures equal to or less than 1/2 psig.

30

CHECKING WIFOLD GM PREWURE

Hit should be necessary to check the manifold gas pressure, connect manometer (water gauge) or other pressure device to the top burner orifice farthest from the manifold inlet and turn burner valve on. For an accurate pressure check have at least 2 other top burners burtig. Be sure the gas supp~ inlet pressure is at least one inch above specified range manifold pressure. The gas supply pressure should never be over 14 inches W.C. men properly adjusted for Natural Gas the W.C. pressure is 4 inches, for ~ Gas the W.C. pressure is 10 inches. The serial plate, located under the main top in the burner box area, indicates for which type of gas your range was factory adjusted.

❑IF MGE WELECTRIC lGNITION-ELE~RIW CONNE~lON

IHFOWION

CA~ON—POR PE~ON~ ~:

DO NOT USE AN -NSION CORD m ~S APPWCE.

. This apptiance must be supptied with the proper voltage and frequency, and connected to an individud, properly grounded and poltied branch circuit, protected by a circuit breaker or timedelay fuse, as noted on the rating plate,

. Wiring must conform to National Electric Codes or the prevaihg locrd code for a range of this kilowati rating. (%e the ratigplate under the main top for this information.)

●E the electric supply

provided does not				‘>
meet the above				~
spectications, d a		‘.	-	Q
ficensed	electrician.			“ fi?.
				D

INSURE PROPER

GROUND EXISTS

w

BEFORE USE.

-NING

E~~CM GROUND~G ~~U~ONS

~s appfiance is equipped tith a tiee prong grounding plug for yom protection against shock h-d and shodd be plugged dire~ inti a proper~ grounded receptacle. Do not cut or remove the grounding prong from this plug.