ge.com

Observe the Following Points in Canning

Safety

Right!

Wrong!

Note: Flat-bottomed canners are required for glass cooktops.

Pots that extend beyond 1″ of the surface element’s circle are not recommended for most surface cooking. However, when canning with water-bath or pressure canner, larger-diameter pots may be used. This is because boiling water temperatures (even under pressure) are not harmful to the cooktop surfaces surrounding the surface elements.

HOWEVER, DO NOT USE LARGE- DIAMETER CANNERS OR OTHER LARGE- DIAMETER POTS FOR FRYING OR BOILING FOODS OTHER THAN WATER. Most syrup or sauce mixtures—and all types of frying—cook at temperatures much higher than boiling water. Such temperatures could eventually harm the glass cooktop surfaces.

Be sure the canner fits over the center of the surface element. If your cooktop or its location does not allow the canner to be centered on the surface element, use smaller-diameter pots for good canning results.

Flat-bottomed canners must be used. Do not use canners with flanged or rippled bottoms (often found in enamelware) because they don’t make enough contact with the surface elements and take a long time to boil water.

When canning, use recipes and procedures from reputable sources. Reliable recipes and procedures are available from the manufacturer of your canner; manufacturers of glass jars for canning, such as Ball and Kerr brand; and the United States Department

of Agriculture Extension Service.

Remember that canning is a process that generates large amounts of steam. To avoid burns from steam or heat, be careful when canning.

NOTE: If your house has low voltage, canning may take longer than expected, even though directions have been carefully followed. The process time will be shortened by:

(1) using a pressure canner, and

(2) starting with HOT tap water for fastest heating of large quantities of water.

CAUTION:

■Safe canning requires that harmful microorganisms are destroyed and that the jars are sealed completely. When canning foods in a water-bath canner, a gentle but steady boil must be maintained for the required time. When canning foods in a pressure canner, the pressure must be maintained for the required time.

■After you have adjusted the controls, it is very important to make sure the prescribed boil or pressure levels are maintained for the required time.

■Since you must make sure to process the canning jars for the prescribed time, with no interruption in processing time, do not can on any cooktop surface element if your canner is not flat.

Instructions

 

Operating Instructions

Instructions

Installation

 

 

 

 

 

 

Troubleshooting Tips

Care and cleaning of the cooktop.

Control Knobs

The control knobs may be removed for easier cleaning.

Make sure the knobs are in the Off positions and pull them straight off the stems for cleaning.

The knobs can be cleaned in a dishwasher or they may also be washed with soap and water. Do not remove chrome accent skirt (on some models). Make sure the insides of the knobs are dry before replacing.

Replace the knobs in the Off position to ensure proper placement.

Consumer Support

9

Page 8 Page 10
Page 9
Image 9
GE JP256 Care and cleaning of the cooktop, Observe the Following Points in Canning, Troubleshooting Tips, Control Knobs
Page 8 Page 10

JP256 specifications

The GE JP256 is an advanced gas turbine designed for high-efficiency power generation, catering to the growing energy demands of both industrial and municipal applications. As part of General Electric's renowned fleet of gas turbines, the JP256 boasts impressive performance metrics that set it apart in the competitive energy landscape.

One of the standout features of the GE JP256 is its combined cycle capability. This technology allows the turbine to work alongside steam turbines, enabling a more efficient use of fuel and improving overall thermal efficiency. This combined cycle setup can achieve efficiencies exceeding 60%, which helps operators reduce fuel costs and minimize greenhouse gas emissions. This is particularly crucial in today's energy market, where there is a strong push toward sustainable practices.

The JP256 is designed with a simple cycle rating, delivering up to 256 MW of power at ISO conditions. This makes it suitable for both peaking and base-load generation, providing flexibility in meeting fluctuating energy demands. Additionally, its low operational and maintenance costs make it an attractive option for utility companies looking to optimize their energy generation portfolio.

In terms of technology, the GE JP256 employs advanced materials and manufacturing techniques, enhancing its durability and performance. The turbine features a high-efficiency airfoil design, which improves aerodynamics and contributes to overall efficiency gains. Its advanced control systems utilize real-time data analytics to optimize performance, ensuring that the turbine operates at maximum efficiency under varying load conditions.

The characteristics of the JP256 also include a modular design that simplifies maintenance and reduces downtime. This design not only eases the replacement of components but also shortens the time required for routine maintenance activities. Moreover, GE’s commitment to innovation is reflected in the turbine's compatibility with various fuels, including natural gas and biogas, allowing for greater operational flexibility.

Noise reduction technologies are also integral to the JP256, making it an optimal choice for installations in urban areas where emissions and noise control are critical. Its compact footprint allows for easier integration into existing plants without requiring significant alterations to infrastructure.

In summary, the GE JP256 gas turbine stands out for its combined cycle capabilities, high efficiency, low operational costs, and advanced technologies. Designed for versatility and sustainability, it is a comprehensive solution for meeting the modern demands of power generation.
Top Page Image Contents