Key Key Description Screen, PR70 HMI Icon Table | Graco instruction

ICON Tables

ICON Descriptions

Key	Key Description	Screen
	Maintenance and Calibration Screens Enter / Exit.	All

	Shot Mode / Operator Control Mode Selection.	Run

	Shot Request (green)	Run, C2,
	Shot Request (green)	C4
		C4

	Red Stop or Cancel (Stops Operation Immediately, regardless of Screen).	All

	Up (Used to Raise Numerical Entry, Screen Navigation or Shot Selection).	Many

	Down (Used to Lower Numerical Entry, Screen Navigation or Shot Selection).	Many

	Enter (Used to Accept Entry).	Many

	Soft (Changes Function, Depending Upon Screen).	All

	Table 2: PR70 HMI ICON Table

ICON	Description	Screen
	Calibration Screens.

	Maintenance Screens.

	Option Abort or Escape.	Many

	Piston Full Extend.	C1, M1

	Piston Full Retract.	C1, M1

	Metering Tube or Cylinder Entrance.	C1

	Phasing Shot.	C2

	Decrease Phasing Shot.	C2

	Increase Phasing Shot.	C2

	Open Displacement Valve (DV) Position Adjustment.	C3

	Tables 3: PR70 Screen ICON Tables

312393G

26 of 50

Image 26

Graco important safety instructions Key Key Description Screen, PR70 HMI Icon Table, Tables 3 PR70 Screen Icon Tables

Contents

PR70 Contents PR70 Accessories Mixer and Shroud Options PR70 Feed System Supplied ManualsRelated Manuals Description Electric Shock Hazard Equipment Misuse Hazard Machine Setup InstallationLocate and Install the PR70 General Information Component Identification Key HMI Control and Indicators PR70 Top View with Shield, Tanks, DV and HMI Removed Run Screen Operation Entering the Setup Screens Machine Disable Mode redSetup Screens Setup Screens with Passwords Enabled PR70 Screen Navigation Diagram Piston Position Calibration C1 Machine PrimingMachine Calibration Open Dispense Valve ODV Setting C3 Phasing C2 Machine Calibration Shots C4 Open Dispense Valve ODV Screen C3 Key Shot Size Definition M2 Ratio Checks Manual Control Options M1 Miscellaneous Machine SetupsPurge Timer / Alarm Settings M2 Manual DV Control Cycle Counter and Silent Mode Control M3 M2 after Purge Shot Size Prompt Date and Time Settings M4 Tank Level Sensing and Velocity Change Options C6 Password Setup / Clearing C5 Setting/Clearing an Administrative Password To clear the password, enter Setting/Clearing a Maintenance only PasswordResetting Passwords HMI Demo Mode Operation Miscellaneous Machine FeaturesHMI Hibernate Mode Limitations of Demo Mode Simulation Error Codes Pressure Relief ProcedureStandby/Shutdown Procedure Error Code Table E50 Error Code TableE29 Tables 3 PR70 Screen Icon Tables Key Key Description ScreenPR70 HMI Icon Table Tables 4 PR70 Screen Icon Tables Run Token MaintenanceSoftware Upgrades, Run Token Troubleshooting Problem Cause Solution Repair Major Mechanical Assemblies, and Attachments Base Frame Assembly PR70 Base Frame Assembly LC0109 Key PR70 Air Cylinder System and Schematic Air Cylinder Assemblies, and Rebuild Kits Air Cylinder Assemblies Pump Assembly Drive Block Assembly Pump Assemblies and Rebuild Kits To install a new Check Valve Rebuild Kit PR70 Check Valve Rebuild Kit LC0093 Key To install a new Rear Pump Rebuild Kit PR70 Rear Pump Rebuild Kit LC0094 Key PR70 Nylon and Uhmwpe Piston Replacement Kits Key Piston Cylinders or Metering Tubes To install a new Piston or Piston/Cylinder Replacement Kit Nylon Pistons see Figure Available PR70 Piston and Cylinder Metering Tubes Kits Key To install a new Piston Plug Assembly Hose Assemblies Heated Piston to DV Hose Assemblies Miscellaneous Mechanical Assemblies To Replace the Fuses PR70 Control Bracket Assembly LC0108 Key PR70 Hydracheck Components Wiring Diagrams PR70 Wiring Interconnect Illustration Wiring Diagram, PR70 Technical Data Category Data Dimensions PR70 Dimensions ON-Board PE Tank version Illustrated Graco Ohio Standard Warranty Graco Information