HMI Control and Indicators | Graco PR70 guide

Component Identification

Key:

A Drive Block

B Hydracheck (optional)

C Check Valve

D Cylinder (Metering Tube)

E Rear Bearing

F Phase Adjustment Screw/Locking

Nut

G Mounting Hole in Base Frame

Figure 4: PR70 Top View with Shield, Tanks, DV and HMI Removed.

HMI Control and Indicators

Figure 5: PR70 HMI Controls

Key:
A	Screen, Display Area	N	Operator Mode ICON
B, D	Up and Down Keys	O	Operator Mode LED
C	Up and Down Key LED	P	Red Stop or Cancel Key (used to stop machine
E	Enter Key LED		operation)
F	Enter Key	Q	Lock Key (used to enter and exit setup screens)
G-J	Soft Keys 1 thru 4 (Left to Right).	R	Green Go Key (used to request a shot)
K	Shot Mode ICON	S	Display area
L	Shot Mode LED	T	Diagnostic LED’s
M	Mode Select Key	U	HMI Rear Access Panel (used to access clock
			battery and for reprogramming the HMI).

312393G

9 of 50

Image 9

Graco important safety instructions HMI Control and Indicators, PR70 Top View with Shield, Tanks, DV and HMI Removed

Contents

PR70 Contents Mixer and Shroud Options PR70 Accessories Related Manuals Supplied ManualsPR70 Feed System Description Electric Shock Hazard Equipment Misuse Hazard Locate and Install the PR70 InstallationMachine Setup General Information Key Component Identification PR70 Top View with Shield, Tanks, DV and HMI Removed HMI Control and Indicators Run Screen Operation Setup Screens Machine Disable Mode redEntering the Setup Screens Setup Screens with Passwords Enabled PR70 Screen Navigation Diagram Machine Priming Machine CalibrationPiston Position Calibration C1 Phasing C2 Open Dispense Valve ODV Setting C3 Open Dispense Valve ODV Screen C3 Key Machine Calibration Shots C4 Ratio Checks Shot Size Definition M2 Purge Timer / Alarm Settings M2 Miscellaneous Machine SetupsManual Control Options M1 Manual DV Control M2 after Purge Shot Size Prompt Cycle Counter and Silent Mode Control M3 Tank Level Sensing and Velocity Change Options C6 Date and Time Settings M4 Setting/Clearing an Administrative Password Password Setup / Clearing C5 Setting/Clearing a Maintenance only Password Resetting PasswordsTo clear the password, enter HMI Hibernate Mode Miscellaneous Machine FeaturesHMI Demo Mode Operation Limitations of Demo Mode Simulation Pressure Relief Procedure Standby/Shutdown ProcedureError Codes Error Code Table Error Code Table E29E50 Key Key Description Screen PR70 HMI Icon TableTables 3 PR70 Screen Icon Tables Tables 4 PR70 Screen Icon Tables Maintenance Software Upgrades, Run TokenRun Token Problem Cause Solution Troubleshooting Major Mechanical Assemblies, and Attachments Repair PR70 Base Frame Assembly LC0109 Key Base Frame Assembly Air Cylinder Assemblies, and Rebuild Kits PR70 Air Cylinder System and Schematic Air Cylinder Assemblies Pump Assembly Pump Assemblies and Rebuild Kits Drive Block Assembly PR70 Check Valve Rebuild Kit LC0093 Key To install a new Check Valve Rebuild Kit PR70 Rear Pump Rebuild Kit LC0094 Key To install a new Rear Pump Rebuild Kit Piston Cylinders or Metering Tubes PR70 Nylon and Uhmwpe Piston Replacement Kits Key Nylon Pistons see Figure To install a new Piston or Piston/Cylinder Replacement Kit Available PR70 Piston and Cylinder Metering Tubes Kits Key Hose Assemblies To install a new Piston Plug Assembly Heated Piston to DV Hose Assemblies To Replace the Fuses Miscellaneous Mechanical Assemblies PR70 Control Bracket Assembly LC0108 Key PR70 Hydracheck Components PR70 Wiring Interconnect Illustration Wiring Diagrams Wiring Diagram, PR70 Category Data Technical Data PR70 Dimensions ON-Board PE Tank version Illustrated Dimensions Graco Information Graco Ohio Standard Warranty