Dimensions | Graco PR70 guide

Technical Data

Dimensions

Figure 36: PR70 Dimensions (ON-Board PE Tank version Illustrated)

A typical PR70 Machine, with the standard On-Board twin 8 liter PE Tanks has the following dimensions:

Dimension	In. (mm)	Dimension	In. (mm)
A (width)	18.49 (469.6)	C (depth)	30.62 (777.7)
B (height)	26.39 (670.3)	D (height in Back)	13.39 (340.1)

A typical PR70 Machine, with the standard On-Board 7.5 liter Stainless Steel Tanks has the following dimensions:

Dimension	In. (mm)	Dimension	In. (mm)
A (width)	15.5 (393.7)	C (depth)	30.62 (777.7)
B (height)	27.37 (695.2)	D (height in Back)	13.39 (340.1)

312393G

49 of 50

Image 49

Graco important safety instructions PR70 Dimensions ON-Board PE Tank version Illustrated

Contents

PR70 Contents Mixer and Shroud Options PR70 Accessories Related Manuals Supplied ManualsPR70 Feed System Description Electric Shock Hazard Equipment Misuse Hazard Locate and Install the PR70 InstallationMachine Setup General Information Key Component Identification PR70 Top View with Shield, Tanks, DV and HMI Removed HMI Control and Indicators Run Screen Operation Setup Screens Machine Disable Mode redEntering the Setup Screens Setup Screens with Passwords Enabled PR70 Screen Navigation Diagram Machine Calibration Machine PrimingPiston Position Calibration C1 Phasing C2 Open Dispense Valve ODV Setting C3 Open Dispense Valve ODV Screen C3 Key Machine Calibration Shots C4 Ratio Checks Shot Size Definition M2 Purge Timer / Alarm Settings M2 Miscellaneous Machine SetupsManual Control Options M1 Manual DV Control M2 after Purge Shot Size Prompt Cycle Counter and Silent Mode Control M3 Tank Level Sensing and Velocity Change Options C6 Date and Time Settings M4 Setting/Clearing an Administrative Password Password Setup / Clearing C5 Resetting Passwords Setting/Clearing a Maintenance only PasswordTo clear the password, enter HMI Hibernate Mode Miscellaneous Machine FeaturesHMI Demo Mode Operation Limitations of Demo Mode Simulation Standby/Shutdown Procedure Pressure Relief ProcedureError Codes Error Code Table E29 Error Code TableE50 PR70 HMI Icon Table Key Key Description ScreenTables 3 PR70 Screen Icon Tables Tables 4 PR70 Screen Icon Tables Software Upgrades, Run Token MaintenanceRun Token Problem Cause Solution Troubleshooting Major Mechanical Assemblies, and Attachments Repair PR70 Base Frame Assembly LC0109 Key Base Frame Assembly Air Cylinder Assemblies, and Rebuild Kits PR70 Air Cylinder System and Schematic Air Cylinder Assemblies Pump Assembly Pump Assemblies and Rebuild Kits Drive Block Assembly PR70 Check Valve Rebuild Kit LC0093 Key To install a new Check Valve Rebuild Kit PR70 Rear Pump Rebuild Kit LC0094 Key To install a new Rear Pump Rebuild Kit Piston Cylinders or Metering Tubes PR70 Nylon and Uhmwpe Piston Replacement Kits Key Nylon Pistons see Figure To install a new Piston or Piston/Cylinder Replacement Kit Available PR70 Piston and Cylinder Metering Tubes Kits Key Hose Assemblies To install a new Piston Plug Assembly Heated Piston to DV Hose Assemblies To Replace the Fuses Miscellaneous Mechanical Assemblies PR70 Control Bracket Assembly LC0108 Key PR70 Hydracheck Components PR70 Wiring Interconnect Illustration Wiring Diagrams Wiring Diagram, PR70 Category Data Technical Data PR70 Dimensions ON-Board PE Tank version Illustrated Dimensions Graco Information Graco Ohio Standard Warranty