|
|
|
|
|
| Use NAT IP |
|
|
|
|
| NAT IP address used in SIP/SDP message. Default is blank. |
| |
|
|
|
|
|
|
|
|
|
|
| Distinctive Ringtone |
| Custom Ring Tone 1 to 3 with associate Caller ID: when selected, if Caller ID is |
|
|
|
| ||
|
|
| configured, then the device will ONLY uses this ring tone when the incoming call is from |
|
|
|
| the Caller ID. System Ring Tone is used for all other calls. When selected but no Caller |
|
|
|
| ID is configured, the selected ring tone will be used for all incoming calls. Distinctive ring |
|
|
|
| tones can be configured not only for matching whole number, but also for matching |
|
|
|
| prefixes. In this case symbol * (star) will be used. |
|
|
|
| If server supports |
|
|
|
| ring tone |
|
|
|
| used. |
|
|
|
| For example: |
|
|
|
| If configured as *617, Ring Tone 1 will be used in case of call arrived from |
|
|
|
| Massachusetts. Any other incoming call will ring using cadence defined in parameter |
|
|
|
| System Ring Cadence located under Advanced Settings Configuration page. |
|
|
|
|
|
|
|
|
|
|
|
| Disable Call Waiting |
| Default is No. If set to YES Call Waiting indication information will not be provided to |
|
|
|
| ||
|
|
| analog phone connected to this FXS port. |
|
|
|
|
|
|
|
|
|
|
|
| Disable Call Waiting |
| Default is No. If set to YES Call Waiting caller ID will not be provided to analog phone |
|
|
|
| ||
| Caller ID |
| connected to this FXS port. |
|
|
|
|
|
|
|
|
|
|
|
| Disable Call Waiting |
| Default is No. This is to disable the stutter Call Waiting Tone when a Call Waiting call |
|
|
|
| ||
| Tone |
| arrives. The CWCID will still be displayed. |
|
|
|
|
|
|
|
|
|
|
|
| Disable Reminder |
| Default is No. This is to disable the Reminder Ring that is played when a call is waiting |
|
|
|
| ||
| Ring for |
| on hold and the analog phone goes |
|
|
|
|
|
|
|
|
|
|
|
| Disable Visual MWI |
| Visual message indicator is a special |
|
|
|
| ||
|
|
| disables the message waiting light on certain phones. GXW40XX has this feature |
|
|
|
| enabled by default. However, certain phones (rare) that do not support it may mistakenly |
|
|
|
| treat this CID signal as an incoming call. A configuration option is needed to turn on MWI |
|
|
|
| in this case. |
|
|
|
|
|
|
|
|
|
|
|
| Visual MWI Type |
| This is the type of signal sent to the analog phone to make it turn the lamp ON upon |
|
|
|
| ||
|
|
| receiving a Voice mail. Check the phone’s manual to find out what signal is supported, |
|
|
|
| FSK (default) or Neon. |
|
|
|
| Note: This is only supported in model GXW4024 ver 4.A or newer. |
|
|
|
|
|
|
|
|
|
|
|
| Ring Timeout |
| Incoming call will stop ringing when not picked up given a specific period of time. |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Hunting Group Ring |
| Default is 20 seconds. If call is not answered within this designated time period, the call |
|
| Timeout |
| will be forwarded to the next member of a Hunt Group. |
|
|
|
|
|
|
|
|
|
|
|
| Delayed Call Forward |
| Default value is 20 seconds. In case this feature activated using * codes (*92 code), the |
|
|
|
| ||
| Wait Timeout |
| call will be forwarded after this preconfigured amount of time. |
|
|
|
|
|
|
|
|
|
|
|
| No Key Entry Timeout |
| Default is 4 seconds. Call will be completed within this time interval if no additional key |
|
|
|
| ||
|
|
| entry occurs. |
|
|
|
|
|
|
Grandstream Networks, Inc. | GXW40XX User Manual | Page 31 of 38 |
| Firmware 1.0.4.2 | Last Updated: 06/2011 |
