Manuals / GSI Outdoors / Kitchen Appliance / Food Processor

GSI Outdoors PNEG-970 operation manual Decals cont, Safety, Rotating Flighting

Models: PNEG-970

1 36

Download 36 pages 40.33 Kb

Page 11

Decals (cont.)

Safety

Decals (cont.)

A.DANGER Sign No. DC-1395 was supplied with your bin unloading equipment. This safety sign should be applied to the side of the bin near the bin opening, so it will be viewed by people entering into the bin storage building. Do not cover any safety signs or any other signs that are already there.

B.If the safety sign location suggested is not in full view because of equipment modifications, other equipment in the area or any reason, then locate the safety sign in a more suitable location.

C.Be certain the surface is clean, dry and free of dirt and oil. Peel paper backing from decals and stick into place. The adhesive backing will bond on contact.

Please remember, safety signs provide important safety information for people working near bin unloading equipment that is in operation.

ROTATING FLIGHTING!

THIS BIN IS EQUIPPED WITH GRAIN AUGERS

WHICH CAN KILL OR DISMEMBER.

KEEP CLEAR OF ALL AUGERS AND NEVER ENTER

THIS BIN UNLESS ALL POWER IS

DISCONNECTED AND LOCKED OUT.

FAILURE TO DO SO WILL RESULT IN

SERIOUS INJURY OR DEATH!

DC-1395

If the Safety Sign cannot be easily read for any reason or has been painted over, replace it immediately.

Additional Safety Signs may be obtained free of charge from your dealer, distributor or ordered from the factory.

Order SAFETY SIGN NO. DC-1395

PNEG-970S2 Hopper w/ Collector Ring

11

Image 11

GSI Outdoors PNEG-970 operation manual Decals cont, Safety, Rotating Flighting

Contents

PNEG-970 PNEG-970Series II Sweep Hopper With Collector Ring Catalog No. Slip Ring Serial No Date of Purchase Inside Back Cover Table of ContentsWarranty SAFETY SafetySafety SAFETY GUIDELINESFOLLOW SAFETY INSTRUCTIONS Safety InstructionsRead and Understand Manual SafetyROTATING FLIGHT DANGER! Rotating FlightOperate Unload Equipment Safely SafetyELECTRICAL WARNINGS Electric Shock HazardSafety INSTALL & OPERATE ELECTRICAL EQUIPMENT PROPERLYPREPARE FOR EMERGENCIES Eye Protection Gloves Steel Toe Boots Respirator Hard HatSafety Keep Emergency Equipment Quickly AccessibleDecal “A” DecalsSafety replaced immediately. Obtain FREE replacements by contacting GSIROTATING FLIGHTING Decals contSafety E m p lo y e e s N a m e p r in te d 7. Operator QualificationsSafety D a te2. General information 3. Capacities and SpecificationsIntroduction 1. Product InformationTemperature & Ampere/Voltage Ratings 4. Slip Ring InformationSpecifications & Listings Introduction1 x 9 3/8 conduit collector ring Assembly1. ASSEMBLE THE CROSSBRACE nine 9 stranded wires 1 chase nipple 1 conduit coupling1/4-20 x 1 hex bolt collector ring lock washer hex nut 1. ASSEMBLE THE CROSSBRACE contAssembly nine 9 stranded wires pivot tube crossbrace assemblycollector ring shield lock washer hex nut Assemblycrossbrace assembly 1/4-20 x 1 hex bolt flat washer 1. ASSEMBLE THE CROSSBRACE conthex nut lock washer flat washer 1/2-13 x 1 3/4 hex bolt Assemblycrossbrace assembly hopper lower tube assembly 1. ASSEMBLE THE CROSSBRACE cont1 x 45 degree flex conduit coupling multi-conductor cord 2. WIRE THE COLLECTOR RINGAssembly NoteThe liquid-tight flex conduit may need to be trimmed to lengthAssembly 2. WIRE THE COLLECTOR RING conthex nut lower tube assembly multi-conductor cord hopper 3. ASSEMBLE THE CROSSBRACE TO THE HOPPERAssembly crossbrace assembly1/2-13 x 1 3/4 hex bolt 3. ASSEMBLE THE CROSSBRACE TO THE HOPPER contAssembly crossbrace assembly hopper hex nut lock washerstranded wires 4. ASSEMBLE THE CROSSBRACE TO THE SWEEPAssembly 1/2-13 x 2 hex bolt pivot rod hex nut pivot tube lockwasher 3. ASSEMBLE THE CROSSBRACE TO THE SWEEP contAssembly flat washerpivot plate 1/2-13 x 1 3/4 hex bolt crossbrace assemblypivot tube 1 conduit coupling 3. WIRE THE COLLECTOR RING TO THE SWEEPAssembly 1 flex conduit couplingAssembly 3. WIRE THE COLLECTOR RING TO THE SWEEP cont1. Preform Pre-Start Checks Start-Up1. Maintain the Hopper MaintenanceA. Lubrication 2. Collector Ring MaintenanceMaintenance solvent cleaning agents to any part of the slipH. Electrical Connections 2. Collector Ring Maintenance ContMaintenance G. Rings1. Intermittent Signal TroubleshootingProblem Solution12 HOPPER COMPONENTS PartsParts 12 & 16 HOPPER COMPONENTSSPEC Collector Ring Replacement PartsConsult the Factory for Custom Application Configurations R A X R DWARRANTY P.O. Box 1004 E. IL. St Assumption IL