Manuals / GSI Outdoors / Kitchen Appliance / Food Processor

GSI Outdoors PNEG-970 ASSEMBLE THE CROSSBRACE TO THE SWEEP cont, Assembly, degree grease fitting

Models: PNEG-970

1 36

Download 36 pages 40.33 Kb

Page 24

Image 24

Assembly

3. ASSEMBLE THE CROSSBRACE TO THE SWEEP (cont.)

C.Connect the pivot plate to the backshield using two (2) 1/2"-13 x 1 3/4" hex bolts, flat washers, lockwashers, and hex nuts.

D.Fasten the pivot rod to the backshield and pivot plate using two (2) 1/2"-13 x 2" hex bolts, lockwashers, and hex nuts.

E.Screw the 45 degree grease fitting into the crossbrace assembly.

1/2"-13 x 2" hex bolt

pivot rod

hex nut

pivot tube

lockwasher

flat washerpivot plate

1/2"-13 x 1 3/4" hex bolt

crossbrace assembly

45 degree grease fitting

24	PNEG-970S2 Hopper w/ Collector Ring

Page 24

Image 24

GSI Outdoors PNEG-970 operation manual ASSEMBLE THE CROSSBRACE TO THE SWEEP cont, Assembly, degree grease fitting

Contents

PNEG-970 Series II Sweep Hopper With Collector RingPNEG-970 Catalog No. Slip Ring Serial No Date of Purchase Table of Contents WarrantyInside Back Cover Safety SAFETYSAFETY GUIDELINES SafetySafety Instructions Read and Understand ManualSafety FOLLOW SAFETY INSTRUCTIONSDANGER! Rotating Flight Operate Unload Equipment SafelySafety ROTATING FLIGHTElectric Shock Hazard SafetyINSTALL & OPERATE ELECTRICAL EQUIPMENT PROPERLY ELECTRICAL WARNINGSEye Protection Gloves Steel Toe Boots Respirator Hard Hat SafetyKeep Emergency Equipment Quickly Accessible PREPARE FOR EMERGENCIESDecals Safetyreplaced immediately. Obtain FREE replacements by contacting GSI Decal “A”Decals cont SafetyROTATING FLIGHTING 7. Operator Qualifications SafetyD a te E m p lo y e e s N a m e p r in te d3. Capacities and Specifications Introduction1. Product Information 2. General information4. Slip Ring Information Specifications & ListingsIntroduction Temperature & Ampere/Voltage RatingsAssembly 1. ASSEMBLE THE CROSSBRACEnine 9 stranded wires 1 chase nipple 1 conduit coupling 1 x 9 3/8 conduit collector ring1. ASSEMBLE THE CROSSBRACE cont Assemblynine 9 stranded wires pivot tube crossbrace assembly 1/4-20 x 1 hex bolt collector ring lock washer hex nutAssembly crossbrace assembly 1/4-20 x 1 hex bolt flat washer1. ASSEMBLE THE CROSSBRACE cont collector ring shield lock washer hex nutAssembly crossbrace assembly hopper lower tube assembly1. ASSEMBLE THE CROSSBRACE cont hex nut lock washer flat washer 1/2-13 x 1 3/4 hex bolt2. WIRE THE COLLECTOR RING AssemblyNoteThe liquid-tight flex conduit may need to be trimmed to length 1 x 45 degree flex conduit coupling multi-conductor cord2. WIRE THE COLLECTOR RING cont Assembly3. ASSEMBLE THE CROSSBRACE TO THE HOPPER Assemblycrossbrace assembly hex nut lower tube assembly multi-conductor cord hopper3. ASSEMBLE THE CROSSBRACE TO THE HOPPER cont Assemblycrossbrace assembly hopper hex nut lock washer 1/2-13 x 1 3/4 hex bolt4. ASSEMBLE THE CROSSBRACE TO THE SWEEP Assemblystranded wires 3. ASSEMBLE THE CROSSBRACE TO THE SWEEP cont Assemblyflat washerpivot plate 1/2-13 x 1 3/4 hex bolt crossbrace assembly 1/2-13 x 2 hex bolt pivot rod hex nut pivot tube lockwasher3. WIRE THE COLLECTOR RING TO THE SWEEP Assembly1 flex conduit coupling pivot tube 1 conduit coupling3. WIRE THE COLLECTOR RING TO THE SWEEP cont AssemblyStart-Up 1. Preform Pre-Start ChecksMaintenance 1. Maintain the Hopper2. Collector Ring Maintenance Maintenancesolvent cleaning agents to any part of the slip A. Lubrication2. Collector Ring Maintenance Cont MaintenanceG. Rings H. Electrical ConnectionsTroubleshooting ProblemSolution 1. Intermittent SignalParts 12 HOPPER COMPONENTS12 & 16 HOPPER COMPONENTS PartsCollector Ring Replacement Parts Consult the Factory for Custom Application ConfigurationsR A X R D SPECWARRANTY P.O. Box 1004 E. IL. St Assumption IL