Manuals / GSI Outdoors / Kitchen Appliance / Food Processor

GSI Outdoors PNEG-970 operation manual Assembly, ASSEMBLE THE CROSSBRACE cont

Models: PNEG-970

1 36

Download 36 pages 40.33 Kb

Page 17

Image 17

Assembly

1. ASSEMBLE THE CROSSBRACE (cont.)

D.Bolt the collector ring shield to the crossbrace assembly using four (4) 1/4"-20 x 1" hex bolts, flat washers, lock washers, and hex nuts. Do not use the remaining bolts.

crossbrace assembly

1/4"-20 x 1" hex bolt flat washer

collector ring shield

lock washer

hex nut

PNEG-970S2 Hopper w/ Collector Ring

Page 17

Image 17

GSI Outdoors PNEG-970 Assembly, ASSEMBLE THE CROSSBRACE cont, crossbrace assembly 1/4-20 x 1 hex bolt flat washer

Contents

PNEG-970 PNEG-970Series II Sweep Hopper With Collector Ring Catalog No. Slip Ring Serial No Date of Purchase Inside Back Cover Table of ContentsWarranty SAFETY SafetySafety SAFETY GUIDELINESRead and Understand Manual Safety InstructionsSafety FOLLOW SAFETY INSTRUCTIONSOperate Unload Equipment Safely DANGER! Rotating FlightSafety ROTATING FLIGHTSafety Electric Shock HazardINSTALL & OPERATE ELECTRICAL EQUIPMENT PROPERLY ELECTRICAL WARNINGSSafety Eye Protection Gloves Steel Toe Boots Respirator Hard HatKeep Emergency Equipment Quickly Accessible PREPARE FOR EMERGENCIESSafety Decalsreplaced immediately. Obtain FREE replacements by contacting GSI Decal “A”ROTATING FLIGHTING Decals contSafety Safety 7. Operator QualificationsD a te E m p lo y e e s N a m e p r in te dIntroduction 3. Capacities and Specifications1. Product Information 2. General informationSpecifications & Listings 4. Slip Ring InformationTemperature & Ampere/Voltage Ratings Introduction1. ASSEMBLE THE CROSSBRACE Assemblynine 9 stranded wires 1 chase nipple 1 conduit coupling 1 x 9 3/8 conduit collector ringAssembly 1. ASSEMBLE THE CROSSBRACE contnine 9 stranded wires pivot tube crossbrace assembly 1/4-20 x 1 hex bolt collector ring lock washer hex nutcrossbrace assembly 1/4-20 x 1 hex bolt flat washer Assembly1. ASSEMBLE THE CROSSBRACE cont collector ring shield lock washer hex nutcrossbrace assembly hopper lower tube assembly Assembly1. ASSEMBLE THE CROSSBRACE cont hex nut lock washer flat washer 1/2-13 x 1 3/4 hex boltAssembly 2. WIRE THE COLLECTOR RINGNoteThe liquid-tight flex conduit may need to be trimmed to length 1 x 45 degree flex conduit coupling multi-conductor cordAssembly 2. WIRE THE COLLECTOR RING contAssembly 3. ASSEMBLE THE CROSSBRACE TO THE HOPPERcrossbrace assembly hex nut lower tube assembly multi-conductor cord hopperAssembly 3. ASSEMBLE THE CROSSBRACE TO THE HOPPER contcrossbrace assembly hopper hex nut lock washer 1/2-13 x 1 3/4 hex boltstranded wires 4. ASSEMBLE THE CROSSBRACE TO THE SWEEPAssembly Assembly 3. ASSEMBLE THE CROSSBRACE TO THE SWEEP contflat washerpivot plate 1/2-13 x 1 3/4 hex bolt crossbrace assembly 1/2-13 x 2 hex bolt pivot rod hex nut pivot tube lockwasherAssembly 3. WIRE THE COLLECTOR RING TO THE SWEEP1 flex conduit coupling pivot tube 1 conduit couplingAssembly 3. WIRE THE COLLECTOR RING TO THE SWEEP cont1. Preform Pre-Start Checks Start-Up1. Maintain the Hopper MaintenanceMaintenance 2. Collector Ring Maintenancesolvent cleaning agents to any part of the slip A. LubricationMaintenance 2. Collector Ring Maintenance ContG. Rings H. Electrical ConnectionsProblem TroubleshootingSolution 1. Intermittent Signal12 HOPPER COMPONENTS PartsParts 12 & 16 HOPPER COMPONENTSConsult the Factory for Custom Application Configurations Collector Ring Replacement PartsR A X R D SPECWARRANTY P.O. Box 1004 E. IL. St Assumption IL