Manuals / GSI Outdoors / Kitchen Appliance / Food Processor

GSI Outdoors PNEG-970 operation manual Assembly, ASSEMBLE THE CROSSBRACE cont

Models: PNEG-970

1 36

Download 36 pages 40.33 Kb

Page 18

Image 18

Assembly

1. ASSEMBLE THE CROSSBRACE (cont.)

E.Slide the lower tube assembly into the shield assembly. Bolt the crossbrace to the hopper using four (4) 1/2"-13 x 1 3/4" hex bolts, flat washers, lock washers, and hex nuts (One on each side.).

hex nut

lock washer

flat washer

1/2"-13 x 1 3/4" hex bolt

crossbrace assembly

hopper

lower tube assembly

F.Slide the lower tube assembly against the hopper and mark the center.

G.Unbolt the crossbrace from the hopper and remove the shield assembly from the crossbrace.

H.Drill a 7/8" hole at the marked location on the hopper.

18	PNEG-970S2 Hopper w/ Collector Ring

Page 18

Image 18

GSI Outdoors PNEG-970 Assembly, ASSEMBLE THE CROSSBRACE cont, hex nut lock washer flat washer 1/2-13 x 1 3/4 hex bolt

Contents

PNEG-970 Series II Sweep Hopper With Collector RingPNEG-970 Catalog No. Slip Ring Serial No Date of Purchase Table of Contents WarrantyInside Back Cover Safety SAFETYSAFETY GUIDELINES SafetySafety Safety InstructionsRead and Understand Manual FOLLOW SAFETY INSTRUCTIONSSafety DANGER! Rotating FlightOperate Unload Equipment Safely ROTATING FLIGHTINSTALL & OPERATE ELECTRICAL EQUIPMENT PROPERLY Electric Shock HazardSafety ELECTRICAL WARNINGSKeep Emergency Equipment Quickly Accessible Eye Protection Gloves Steel Toe Boots Respirator Hard HatSafety PREPARE FOR EMERGENCIESreplaced immediately. Obtain FREE replacements by contacting GSI DecalsSafety Decal “A”Decals cont SafetyROTATING FLIGHTING D a te 7. Operator QualificationsSafety E m p lo y e e s N a m e p r in te d1. Product Information 3. Capacities and SpecificationsIntroduction 2. General informationTemperature & Ampere/Voltage Ratings 4. Slip Ring InformationSpecifications & Listings Introductionnine 9 stranded wires 1 chase nipple 1 conduit coupling Assembly1. ASSEMBLE THE CROSSBRACE 1 x 9 3/8 conduit collector ringnine 9 stranded wires pivot tube crossbrace assembly 1. ASSEMBLE THE CROSSBRACE contAssembly 1/4-20 x 1 hex bolt collector ring lock washer hex nut1. ASSEMBLE THE CROSSBRACE cont Assemblycrossbrace assembly 1/4-20 x 1 hex bolt flat washer collector ring shield lock washer hex nut1. ASSEMBLE THE CROSSBRACE cont Assemblycrossbrace assembly hopper lower tube assembly hex nut lock washer flat washer 1/2-13 x 1 3/4 hex boltNoteThe liquid-tight flex conduit may need to be trimmed to length 2. WIRE THE COLLECTOR RINGAssembly 1 x 45 degree flex conduit coupling multi-conductor cord2. WIRE THE COLLECTOR RING cont Assemblycrossbrace assembly 3. ASSEMBLE THE CROSSBRACE TO THE HOPPERAssembly hex nut lower tube assembly multi-conductor cord hoppercrossbrace assembly hopper hex nut lock washer 3. ASSEMBLE THE CROSSBRACE TO THE HOPPER contAssembly 1/2-13 x 1 3/4 hex bolt4. ASSEMBLE THE CROSSBRACE TO THE SWEEP Assemblystranded wires flat washerpivot plate 1/2-13 x 1 3/4 hex bolt crossbrace assembly 3. ASSEMBLE THE CROSSBRACE TO THE SWEEP contAssembly 1/2-13 x 2 hex bolt pivot rod hex nut pivot tube lockwasher1 flex conduit coupling 3. WIRE THE COLLECTOR RING TO THE SWEEPAssembly pivot tube 1 conduit coupling3. WIRE THE COLLECTOR RING TO THE SWEEP cont AssemblyStart-Up 1. Preform Pre-Start ChecksMaintenance 1. Maintain the Hoppersolvent cleaning agents to any part of the slip 2. Collector Ring MaintenanceMaintenance A. LubricationG. Rings 2. Collector Ring Maintenance ContMaintenance H. Electrical ConnectionsSolution TroubleshootingProblem 1. Intermittent SignalParts 12 HOPPER COMPONENTS12 & 16 HOPPER COMPONENTS PartsR A X R D Collector Ring Replacement PartsConsult the Factory for Custom Application Configurations SPECWARRANTY P.O. Box 1004 E. IL. St Assumption IL