Manuals / GSI Outdoors / Kitchen Appliance / Food Processor

GSI Outdoors PNEG-970 operation manual Table of Contents, Warranty, Inside Back Cover

Models: PNEG-970

1 36

Page 3

Personnel operating or working around this equipment should read this manual. This manual must be delivered with equipment to its owner. Failure to read this manual and its safety instructions is a misuse of the equipment. Any misuse of the equipment may void the warranty.

1.	Safety	4
2.	Introduction	13
3.	Assembly	15
4.	Startup	27
5.	Maintenance	28
6.	Troubleshooting	31
7.	Parts List	32
8.	Warranty	Inside Back Cover

PNEG-970S2 Hopper w/ Collector Ring

Page 3

Image 3

Contents

PNEG-970 Series II Sweep Hopper With Collector RingPNEG-970 Catalog No. Slip Ring Serial No Date of Purchase Table of Contents WarrantyInside Back Cover SAFETY SafetySafety SAFETY GUIDELINESFOLLOW SAFETY INSTRUCTIONS Safety InstructionsRead and Understand Manual SafetyROTATING FLIGHT DANGER! Rotating FlightOperate Unload Equipment Safely SafetyELECTRICAL WARNINGS Electric Shock HazardSafety INSTALL & OPERATE ELECTRICAL EQUIPMENT PROPERLYPREPARE FOR EMERGENCIES Eye Protection Gloves Steel Toe Boots Respirator Hard HatSafety Keep Emergency Equipment Quickly AccessibleDecal “A” DecalsSafety replaced immediately. Obtain FREE replacements by contacting GSIDecals cont SafetyROTATING FLIGHTING E m p lo y e e s N a m e p r in te d 7. Operator QualificationsSafety D a te2. General information 3. Capacities and SpecificationsIntroduction 1. Product InformationIntroduction 4. Slip Ring InformationSpecifications & Listings Temperature & Ampere/Voltage Ratings1 x 9 3/8 conduit collector ring Assembly1. ASSEMBLE THE CROSSBRACE nine 9 stranded wires 1 chase nipple 1 conduit coupling1/4-20 x 1 hex bolt collector ring lock washer hex nut 1. ASSEMBLE THE CROSSBRACE contAssembly nine 9 stranded wires pivot tube crossbrace assemblycollector ring shield lock washer hex nut Assemblycrossbrace assembly 1/4-20 x 1 hex bolt flat washer 1. ASSEMBLE THE CROSSBRACE conthex nut lock washer flat washer 1/2-13 x 1 3/4 hex bolt Assemblycrossbrace assembly hopper lower tube assembly 1. ASSEMBLE THE CROSSBRACE cont1 x 45 degree flex conduit coupling multi-conductor cord 2. WIRE THE COLLECTOR RINGAssembly NoteThe liquid-tight flex conduit may need to be trimmed to lengthAssembly 2. WIRE THE COLLECTOR RING conthex nut lower tube assembly multi-conductor cord hopper 3. ASSEMBLE THE CROSSBRACE TO THE HOPPERAssembly crossbrace assembly1/2-13 x 1 3/4 hex bolt 3. ASSEMBLE THE CROSSBRACE TO THE HOPPER contAssembly crossbrace assembly hopper hex nut lock washer4. ASSEMBLE THE CROSSBRACE TO THE SWEEP Assemblystranded wires 1/2-13 x 2 hex bolt pivot rod hex nut pivot tube lockwasher 3. ASSEMBLE THE CROSSBRACE TO THE SWEEP contAssembly flat washerpivot plate 1/2-13 x 1 3/4 hex bolt crossbrace assemblypivot tube 1 conduit coupling 3. WIRE THE COLLECTOR RING TO THE SWEEPAssembly 1 flex conduit couplingAssembly 3. WIRE THE COLLECTOR RING TO THE SWEEP cont1. Preform Pre-Start Checks Start-Up1. Maintain the Hopper MaintenanceA. Lubrication 2. Collector Ring MaintenanceMaintenance solvent cleaning agents to any part of the slipH. Electrical Connections 2. Collector Ring Maintenance ContMaintenance G. Rings1. Intermittent Signal TroubleshootingProblem Solution12 HOPPER COMPONENTS PartsParts 12 & 16 HOPPER COMPONENTSSPEC Collector Ring Replacement PartsConsult the Factory for Custom Application Configurations R A X R DWARRANTY P.O. Box 1004 E. IL. St Assumption IL