Manuals / GSI Outdoors / Kitchen Appliance / Food Processor

GSI Outdoors PNEG-970 Assemble The Crossbrace To The Sweep, Assembly, stranded wires

Models: PNEG-970

1 36

Download 36 pages 40.33 Kb

Page 23

Image 23

Assembly

4. ASSEMBLE THE CROSSBRACE TO THE SWEEP

A.Feed the nine (9) stranded wires from the collector ring through the pivot tube and hole in the back of the sweep head section.

B.Align the hole in the backshield with the pivot tube and push the sweep onto the pivot tube.

stranded wires

PNEG-970S2 Hopper w/ Collector Ring

Page 23

Image 23

GSI Outdoors PNEG-970 operation manual Assemble The Crossbrace To The Sweep, Assembly, stranded wires

Contents

PNEG-970 PNEG-970Series II Sweep Hopper With Collector Ring Catalog No. Slip Ring Serial No Date of Purchase Inside Back Cover Table of ContentsWarranty SAFETY SafetySafety SAFETY GUIDELINESFOLLOW SAFETY INSTRUCTIONS Safety InstructionsRead and Understand Manual SafetyROTATING FLIGHT DANGER! Rotating FlightOperate Unload Equipment Safely SafetyELECTRICAL WARNINGS Electric Shock HazardSafety INSTALL & OPERATE ELECTRICAL EQUIPMENT PROPERLYPREPARE FOR EMERGENCIES Eye Protection Gloves Steel Toe Boots Respirator Hard HatSafety Keep Emergency Equipment Quickly AccessibleDecal “A” DecalsSafety replaced immediately. Obtain FREE replacements by contacting GSIROTATING FLIGHTING Decals contSafety E m p lo y e e s N a m e p r in te d 7. Operator QualificationsSafety D a te2. General information 3. Capacities and SpecificationsIntroduction 1. Product InformationIntroduction 4. Slip Ring InformationSpecifications & Listings Temperature & Ampere/Voltage Ratings1 x 9 3/8 conduit collector ring Assembly1. ASSEMBLE THE CROSSBRACE nine 9 stranded wires 1 chase nipple 1 conduit coupling1/4-20 x 1 hex bolt collector ring lock washer hex nut 1. ASSEMBLE THE CROSSBRACE contAssembly nine 9 stranded wires pivot tube crossbrace assemblycollector ring shield lock washer hex nut Assemblycrossbrace assembly 1/4-20 x 1 hex bolt flat washer 1. ASSEMBLE THE CROSSBRACE conthex nut lock washer flat washer 1/2-13 x 1 3/4 hex bolt Assemblycrossbrace assembly hopper lower tube assembly 1. ASSEMBLE THE CROSSBRACE cont1 x 45 degree flex conduit coupling multi-conductor cord 2. WIRE THE COLLECTOR RINGAssembly NoteThe liquid-tight flex conduit may need to be trimmed to lengthAssembly 2. WIRE THE COLLECTOR RING conthex nut lower tube assembly multi-conductor cord hopper 3. ASSEMBLE THE CROSSBRACE TO THE HOPPERAssembly crossbrace assembly1/2-13 x 1 3/4 hex bolt 3. ASSEMBLE THE CROSSBRACE TO THE HOPPER contAssembly crossbrace assembly hopper hex nut lock washerstranded wires 4. ASSEMBLE THE CROSSBRACE TO THE SWEEPAssembly 1/2-13 x 2 hex bolt pivot rod hex nut pivot tube lockwasher 3. ASSEMBLE THE CROSSBRACE TO THE SWEEP contAssembly flat washerpivot plate 1/2-13 x 1 3/4 hex bolt crossbrace assemblypivot tube 1 conduit coupling 3. WIRE THE COLLECTOR RING TO THE SWEEPAssembly 1 flex conduit couplingAssembly 3. WIRE THE COLLECTOR RING TO THE SWEEP cont1. Preform Pre-Start Checks Start-Up1. Maintain the Hopper MaintenanceA. Lubrication 2. Collector Ring MaintenanceMaintenance solvent cleaning agents to any part of the slipH. Electrical Connections 2. Collector Ring Maintenance ContMaintenance G. Rings1. Intermittent Signal TroubleshootingProblem Solution12 HOPPER COMPONENTS PartsParts 12 & 16 HOPPER COMPONENTSSPEC Collector Ring Replacement PartsConsult the Factory for Custom Application Configurations R A X R DWARRANTY P.O. Box 1004 E. IL. St Assumption IL