Manuals / GSI Outdoors / Kitchen Appliance / Food Processor

GSI Outdoors PNEG-970 operation manual WIRE THE COLLECTOR RING cont, Assembly

Models: PNEG-970

1 36

Download 36 pages 40.33 Kb

Page 20

Image 20

Assembly

2. WIRE THE COLLECTOR RING (cont.)

F.Wire the multi-conductor cord to the collector ring using the fork terminals provided in the following manner.

1.Thermal Protection Leads

a.Wire the "P1" lead from the control panel to ring "1".

b.Wire the "P2" lead from the control panel to ring "2".

2.Drive Motor Leads

a.Wire the three (3) power leads to rings "3", "4", and "5".

b.Wire the ground lead to ring "9".

3.Auger Motor Leads

a.Wire the three (3) power leads to rings "6", "7", and "8".

b.Wire the ground lead to ring "9".

G.Replace the protective housing onto the collector ring.

20	PNEG-970S2 Hopper w/ Collector Ring

Page 20

Image 20

GSI Outdoors PNEG-970 operation manual WIRE THE COLLECTOR RING cont, Assembly

Contents

PNEG-970 PNEG-970Series II Sweep Hopper With Collector Ring Catalog No. Slip Ring Serial No Date of Purchase Inside Back Cover Table of ContentsWarranty Safety SAFETYSAFETY GUIDELINES SafetySafety Instructions Read and Understand ManualSafety FOLLOW SAFETY INSTRUCTIONSDANGER! Rotating Flight Operate Unload Equipment SafelySafety ROTATING FLIGHTElectric Shock Hazard SafetyINSTALL & OPERATE ELECTRICAL EQUIPMENT PROPERLY ELECTRICAL WARNINGSEye Protection Gloves Steel Toe Boots Respirator Hard Hat SafetyKeep Emergency Equipment Quickly Accessible PREPARE FOR EMERGENCIESDecals Safetyreplaced immediately. Obtain FREE replacements by contacting GSI Decal “A”ROTATING FLIGHTING Decals contSafety 7. Operator Qualifications SafetyD a te E m p lo y e e s N a m e p r in te d3. Capacities and Specifications Introduction1. Product Information 2. General information4. Slip Ring Information Specifications & ListingsTemperature & Ampere/Voltage Ratings IntroductionAssembly 1. ASSEMBLE THE CROSSBRACEnine 9 stranded wires 1 chase nipple 1 conduit coupling 1 x 9 3/8 conduit collector ring1. ASSEMBLE THE CROSSBRACE cont Assemblynine 9 stranded wires pivot tube crossbrace assembly 1/4-20 x 1 hex bolt collector ring lock washer hex nutAssembly crossbrace assembly 1/4-20 x 1 hex bolt flat washer1. ASSEMBLE THE CROSSBRACE cont collector ring shield lock washer hex nutAssembly crossbrace assembly hopper lower tube assembly1. ASSEMBLE THE CROSSBRACE cont hex nut lock washer flat washer 1/2-13 x 1 3/4 hex bolt2. WIRE THE COLLECTOR RING AssemblyNoteThe liquid-tight flex conduit may need to be trimmed to length 1 x 45 degree flex conduit coupling multi-conductor cord2. WIRE THE COLLECTOR RING cont Assembly3. ASSEMBLE THE CROSSBRACE TO THE HOPPER Assemblycrossbrace assembly hex nut lower tube assembly multi-conductor cord hopper3. ASSEMBLE THE CROSSBRACE TO THE HOPPER cont Assemblycrossbrace assembly hopper hex nut lock washer 1/2-13 x 1 3/4 hex boltstranded wires 4. ASSEMBLE THE CROSSBRACE TO THE SWEEPAssembly 3. ASSEMBLE THE CROSSBRACE TO THE SWEEP cont Assemblyflat washerpivot plate 1/2-13 x 1 3/4 hex bolt crossbrace assembly 1/2-13 x 2 hex bolt pivot rod hex nut pivot tube lockwasher3. WIRE THE COLLECTOR RING TO THE SWEEP Assembly1 flex conduit coupling pivot tube 1 conduit coupling3. WIRE THE COLLECTOR RING TO THE SWEEP cont AssemblyStart-Up 1. Preform Pre-Start ChecksMaintenance 1. Maintain the Hopper2. Collector Ring Maintenance Maintenancesolvent cleaning agents to any part of the slip A. Lubrication2. Collector Ring Maintenance Cont MaintenanceG. Rings H. Electrical ConnectionsTroubleshooting ProblemSolution 1. Intermittent SignalParts 12 HOPPER COMPONENTS12 & 16 HOPPER COMPONENTS PartsCollector Ring Replacement Parts Consult the Factory for Custom Application ConfigurationsR A X R D SPECWARRANTY P.O. Box 1004 E. IL. St Assumption IL