Manuals / GSI Outdoors / Kitchen Appliance / Food Processor

GSI Outdoors PNEG-970 Wire The Collector Ring, Assembly, collector ring hub, 1 x 16 flex conduit

Models: PNEG-970

1 36

Download 36 pages 40.33 Kb

Page 19

2. WIRE THE COLLECTOR RING

Assembly

2. WIRE THE COLLECTOR RING

Electrical controls and wiring should be installed by a qualified electrician. The motor disconnect switches and conductor cables should comply with the National Electrical code and any local codes which apply. Reset and motor starting stations should be located so that the operator can see that all personnel are clear of the equipment.

Note:The liquid-tight flex conduit may need to be trimmed to length.

A.Attach the 1" liquid-tight flex conduit coupling to one end of the 1" x 16" liquid-tight flex conduit.

B.Attach the 1" x 45 degree liquid-tight flex conduit coupling to the other end of the 1" x 16" liquid tight flex conduit.

C.Remove the protective housing from the collector ring.

D.Feed the multi-conductor cord through the conduit assembly and the 1" conduit hub on the collector ring.

E.Attach the 1" x 45 degree liquid-tight flex conduit coupling to the 1" conduit hub on the collector ring. Be sure to turn the conduit assembly down .

1" x 45 degree flex conduit coupling

multi-conductor cord

collector ring hub	1" x 16" flex conduit

1" flex conduit coupling

PNEG-970S2 Hopper w/ Collector Ring

19

Image 19

GSI Outdoors PNEG-970 Wire The Collector Ring, Assembly, 1 x 45 degree flex conduit coupling multi-conductor cord

Contents

Series II Sweep Hopper With Collector Ring PNEG-970PNEG-970 Catalog No. Slip Ring Serial No Date of Purchase Warranty Table of ContentsInside Back Cover SAFETY SafetySafety SAFETY GUIDELINESFOLLOW SAFETY INSTRUCTIONS Safety InstructionsRead and Understand Manual SafetyROTATING FLIGHT DANGER! Rotating FlightOperate Unload Equipment Safely SafetyELECTRICAL WARNINGS Electric Shock HazardSafety INSTALL & OPERATE ELECTRICAL EQUIPMENT PROPERLYPREPARE FOR EMERGENCIES Eye Protection Gloves Steel Toe Boots Respirator Hard HatSafety Keep Emergency Equipment Quickly AccessibleDecal “A” DecalsSafety replaced immediately. Obtain FREE replacements by contacting GSISafety Decals contROTATING FLIGHTING E m p lo y e e s N a m e p r in te d 7. Operator QualificationsSafety D a te2. General information 3. Capacities and SpecificationsIntroduction 1. Product InformationTemperature & Ampere/Voltage Ratings 4. Slip Ring InformationSpecifications & Listings Introduction1 x 9 3/8 conduit collector ring Assembly1. ASSEMBLE THE CROSSBRACE nine 9 stranded wires 1 chase nipple 1 conduit coupling1/4-20 x 1 hex bolt collector ring lock washer hex nut 1. ASSEMBLE THE CROSSBRACE contAssembly nine 9 stranded wires pivot tube crossbrace assemblycollector ring shield lock washer hex nut Assemblycrossbrace assembly 1/4-20 x 1 hex bolt flat washer 1. ASSEMBLE THE CROSSBRACE conthex nut lock washer flat washer 1/2-13 x 1 3/4 hex bolt Assemblycrossbrace assembly hopper lower tube assembly 1. ASSEMBLE THE CROSSBRACE cont1 x 45 degree flex conduit coupling multi-conductor cord 2. WIRE THE COLLECTOR RINGAssembly NoteThe liquid-tight flex conduit may need to be trimmed to lengthAssembly 2. WIRE THE COLLECTOR RING conthex nut lower tube assembly multi-conductor cord hopper 3. ASSEMBLE THE CROSSBRACE TO THE HOPPERAssembly crossbrace assembly1/2-13 x 1 3/4 hex bolt 3. ASSEMBLE THE CROSSBRACE TO THE HOPPER contAssembly crossbrace assembly hopper hex nut lock washerAssembly 4. ASSEMBLE THE CROSSBRACE TO THE SWEEPstranded wires 1/2-13 x 2 hex bolt pivot rod hex nut pivot tube lockwasher 3. ASSEMBLE THE CROSSBRACE TO THE SWEEP contAssembly flat washerpivot plate 1/2-13 x 1 3/4 hex bolt crossbrace assemblypivot tube 1 conduit coupling 3. WIRE THE COLLECTOR RING TO THE SWEEPAssembly 1 flex conduit couplingAssembly 3. WIRE THE COLLECTOR RING TO THE SWEEP cont1. Preform Pre-Start Checks Start-Up1. Maintain the Hopper MaintenanceA. Lubrication 2. Collector Ring MaintenanceMaintenance solvent cleaning agents to any part of the slipH. Electrical Connections 2. Collector Ring Maintenance ContMaintenance G. Rings1. Intermittent Signal TroubleshootingProblem Solution12 HOPPER COMPONENTS PartsParts 12 & 16 HOPPER COMPONENTSSPEC Collector Ring Replacement PartsConsult the Factory for Custom Application Configurations R A X R DWARRANTY P.O. Box 1004 E. IL. St Assumption IL