Manuals / GSI Outdoors / Kitchen Appliance / Food Processor

GSI Outdoors PNEG-970 operation manual Maintenance, Maintain the Hopper

Models: PNEG-970

1 36

Download 36 pages 40.33 Kb

Page 28

Image 28

Maintenance

1. Maintain the Hopper

ALWAYS shutdown and disconnect the power supply before adjusting, servicing or cleaning the equipment.

A.Use caution when repairing or replacing equipment parts.

B.Make sure ALL decals are legible and tightly attached to the hopper. If necessary, replace them FREE OF CHARGE by contacting GSI at:

GSI

P.O. Box 20

1004 E. Illinois St.

Assumption, IL 62510

(217)226-4421

C.Make sure ALL electrical wiring is not damaged, and that it meets proper wiring codes.

D.Make sure ALL components are in good working condition before use.

E.Grease the center pivot tube at least two (2) times each season.

28	PNEG-970S2 Hopper w/ Collector Ring

Page 28

Image 28

GSI Outdoors PNEG-970 operation manual Maintenance, Maintain the Hopper

Contents

Series II Sweep Hopper With Collector Ring PNEG-970PNEG-970 Catalog No. Slip Ring Serial No Date of Purchase Warranty Table of ContentsInside Back Cover Safety SAFETYSAFETY GUIDELINES SafetySafety Instructions Read and Understand ManualSafety FOLLOW SAFETY INSTRUCTIONSDANGER! Rotating Flight Operate Unload Equipment SafelySafety ROTATING FLIGHTElectric Shock Hazard SafetyINSTALL & OPERATE ELECTRICAL EQUIPMENT PROPERLY ELECTRICAL WARNINGSEye Protection Gloves Steel Toe Boots Respirator Hard Hat SafetyKeep Emergency Equipment Quickly Accessible PREPARE FOR EMERGENCIESDecals Safetyreplaced immediately. Obtain FREE replacements by contacting GSI Decal “A”Safety Decals contROTATING FLIGHTING 7. Operator Qualifications SafetyD a te E m p lo y e e s N a m e p r in te d3. Capacities and Specifications Introduction1. Product Information 2. General information4. Slip Ring Information Specifications & ListingsTemperature & Ampere/Voltage Ratings IntroductionAssembly 1. ASSEMBLE THE CROSSBRACEnine 9 stranded wires 1 chase nipple 1 conduit coupling 1 x 9 3/8 conduit collector ring1. ASSEMBLE THE CROSSBRACE cont Assemblynine 9 stranded wires pivot tube crossbrace assembly 1/4-20 x 1 hex bolt collector ring lock washer hex nutAssembly crossbrace assembly 1/4-20 x 1 hex bolt flat washer1. ASSEMBLE THE CROSSBRACE cont collector ring shield lock washer hex nutAssembly crossbrace assembly hopper lower tube assembly1. ASSEMBLE THE CROSSBRACE cont hex nut lock washer flat washer 1/2-13 x 1 3/4 hex bolt2. WIRE THE COLLECTOR RING AssemblyNoteThe liquid-tight flex conduit may need to be trimmed to length 1 x 45 degree flex conduit coupling multi-conductor cord2. WIRE THE COLLECTOR RING cont Assembly3. ASSEMBLE THE CROSSBRACE TO THE HOPPER Assemblycrossbrace assembly hex nut lower tube assembly multi-conductor cord hopper3. ASSEMBLE THE CROSSBRACE TO THE HOPPER cont Assemblycrossbrace assembly hopper hex nut lock washer 1/2-13 x 1 3/4 hex boltAssembly 4. ASSEMBLE THE CROSSBRACE TO THE SWEEPstranded wires 3. ASSEMBLE THE CROSSBRACE TO THE SWEEP cont Assemblyflat washerpivot plate 1/2-13 x 1 3/4 hex bolt crossbrace assembly 1/2-13 x 2 hex bolt pivot rod hex nut pivot tube lockwasher3. WIRE THE COLLECTOR RING TO THE SWEEP Assembly1 flex conduit coupling pivot tube 1 conduit coupling3. WIRE THE COLLECTOR RING TO THE SWEEP cont AssemblyStart-Up 1. Preform Pre-Start ChecksMaintenance 1. Maintain the Hopper2. Collector Ring Maintenance Maintenancesolvent cleaning agents to any part of the slip A. Lubrication2. Collector Ring Maintenance Cont MaintenanceG. Rings H. Electrical ConnectionsTroubleshooting ProblemSolution 1. Intermittent SignalParts 12 HOPPER COMPONENTS12 & 16 HOPPER COMPONENTS PartsCollector Ring Replacement Parts Consult the Factory for Custom Application ConfigurationsR A X R D SPECWARRANTY P.O. Box 1004 E. IL. St Assumption IL