INSTALLATION
7.When a compatible code set is found, press the OK Button to program it into the Source Selector.
8.Check that other functions control the device correctly. Sometimes manufacturers use the same Power code for several models, while other codes vary. Repeat this process until you’ve pro- grammed a satisfactory code set that operates most functions.
To change the device type of a Source Selector:
If your system includes two products of one device type but no product corresponding to a different Source Selector, you may program one product into its corresponding Source Selector, and change another Source Selector’s device type to program the second product by following this procedure:
1.Access the remote’s menu system by pressing and holding the AVR Settings Button for 3 seconds, until the “Main Menu” and “Program Device” messages appear in the LCD Display.
2.Use the 1/5Buttons to select “Change Device Type” from the remote’s main menu, and press the OK Button.
3.Use the 1/5 Buttons to select the Source Selector whose device type you wish to change, and press the OK Button. Your selection will appear on the left side of the lower line, while the choice of new device types will appear on the right side.
4.Use the 1/5 Buttons to select the new device type you wish to assign to the Source Selector, and press the OK Button.
5.Program your product into the Source Selector by choosing the brand, then searching for a compatible code set, as described in the preceding section. If you allow the remote to “time out”, then the device type reassignment will not take effect.
To “learn” individual key codes:
If some functions do not work correctly, you may reprogram individual keys from the device’s original remote by following this procedure:
1.Place the two remotes with their IR transmitters facing each other, about one inch apart. See Figure 19.
Figure 19 – AVR and Device Remotes “Head to Head”
2.Access the remote’s menu system by pressing and holding the AVR Settings Button for 3 seconds, until the “Main Menu” and “Program Device” messages appear in the LCD Display.
3.Use the 1/5Buttons to select “Learn” from the remote’s main menu, and press the OK Button.
4.When the “Learn Menu” message appears in the upper line of the LCD Display, make sure the “Learn” message appears in the lower line (not “Learn Delete”), and press the OK Button.
5.Use the 1/5Buttons to select the device you wish to learn a code for, and press the OK Button.
6.Press the destination button, and the menu will prompt you to press the key on the original remote whose code you wish to program into the destination button. You may learn a new code into the following buttons: Device Power On/Off, Alphanumeric Keys, Last Button, Back/Exit Button, Menu Button, Navigation
Buttons, OK Button, Disc Menu Button, the four Soft Keys, Channel Up/Down, Volume Up/Down, Mute and the Transport Controls (including Record).
NOTE: If you press the wrong destination button and wish to cancel the learning process, you must wait about 30 seconds for the remote to “time out”. It will exit its program mode and return to normal operation, and you may begin again. Pressing another button will have no effect.
7.Press the key on the original remote, and if the code was learned correctly, the Navigation and OK Buttons will light up. The Learn Menu will prompt you to learn another key, rename the key just learned or exit Learn mode. Use the 1/5Buttons to make your selection, and press the OK Button.
To delete a programmed or learned code:
1.Access the remote’s menu system by pressing and holding the AVR Settings Button for 3 seconds, until the “Main Menu” and “Program Device” messages appear in the LCD Display.
2.Use the 1/5Buttons to select “Learn” from the remote’s main menu, and press the OK Button.
3.When the “Learn Menu” message appears in the upper line of the LCD Display, scroll to the “Learn Delete” option, and press the OK Button.
4.The Learn Delete menu offers the options of deleting a single learned key code, an entire device or all devices. Scroll to the desired option and press the OK Button.
•To delete an individual key code, the remote will first prompt you to select the device containing the key code, then prompt you to press the key. It will confirm the deletion, then offer you the opportunity to delete another learned key or exit the delete key function.
•To delete an entire device, the remote will prompt you to select the device. When you scroll to the device and press the OK Button, the remote will confirm the deletion and exit its programming mode, returning to normal operation.
•To delete all devices, wait a few moments while the remote deletes all programmed device codes. It will then return to normal operation.
To rename a key or device:
If you wish to change the name of a device or key as it appears in the LCD Display, follow these steps:
1.Access the remote’s menu system by pressing and holding the AVR Settings Button for 3 seconds, until the “Main Menu” and “Program Device” messages appear in the LCD Display.
2.Use the 1/5 Buttons to select “Rename” and press the OK Button.
3.Use the 1/5 Buttons to select whether to rename a device or a key, and press the OK Button.
4.Use the 1/5 Buttons to select the device, either to rename the device itself or a key function used by that device, and press the OK Button.
5.The current name of the device or key will appear on the lower line of the LCD Display, with the cursor at the end of the line.
27
