Step Fifteen Turn On the AVR 7550HD | Harman-Kardon specs

INSTALLATION

Use the 7Button to move the cursor to the beginning of the name, then type over the current name using the Alphanumeric Keys.

Each Alphanumeric Key has the characters available in addition to its number printed above the key. Each press of the key scrolls through the available characters. To move to the next character, either press the 3Button or press the next desired Alphanumeric Key.

Press the OK Button to finish, and the remote will prompt you to rename another key or device, or to exit.

STEP FIFTEEN – Turn On the AVR 7550HD

Two steps are required the first time you turn on the AVR 7550HD.

1.Flip down the Front-Panel Door and press the Main Power Switch in. The Power Indicator on the front panel will turn amber, indi- cating that the AVR is in Standby mode and is ready to be turned on. Normally, you may leave the Main Power Switch on, even when the receiver is not being used.

2.There are several ways to turn on the AVR from Standby mode.

a)Press the Standby/On Switch on the front panel.

b)Using the remote, press the AVR Power On Button or any of the Source Selectors.

NOTES:

•Any time you press one of the Source Selectors on the remote, the remote will switch device modes. To control the receiver, press the AVR Settings Button. Some AVR functions are available in all device modes: Volume Controls (including Mute), Audio Effects, Video Modes, Surround Modes, AVR Settings, Info Settings, Sleep Settings and AVR Power On and Off.

•If you do not see a picture within about 1 minute, refer to the Video Troubleshooting Tips on page 34.

28

Image 28

Harman-Kardon owner manual Step Fifteen Turn On the AVR 7550HD

Contents

AVR7550HD Safety Information Important Safety InstructionsService Instructions Outdoor Use Marking Wet Location Marking Important Safety Information Unpacking Table of Contents Introduction Surround Modes Supplied Accessories Audio InputsAudio/Video Inputs Digital Audio Inputs FRONT-PANEL Controls Back/Exit On When the AVR is turned on, this LED turns white Resolution setting 480i, 480p, 720p, 1080i or 1080p REAR-PANEL Connections Video Hdmi 1, 2, 3 Output XM Antenna REAR-PANEL Connections Front, Center and Surround Speaker Outputs AVR Power On Main Remote Control FunctionsZone Selector Main Remote Control Functions Main Remote Control Functions Zone 2 Remote Control Functions Sleep SettingsIR Transmitter Mute Menu Zone 2 Remote Control Functions Introduction to Home Theater Typical Home Theater SystemMultichannel Audio Harman International the Harman Kardon parent company Logic Connecting Source Devices to the AVR ConnectionsSpeaker Connections Subwoofer Video Connections Including Dolby TrueHD and DTS-HD Master AudioAnalog Audio Digital Video Antennas RS-232 Serial Port Front Speaker Placement Speaker PlacementSubwoofer Placement Best audio connection for each source For Getting StartedSource Assignment Worksheet Getting Started Installation Step Eleven Install a Multizone System Connect a Video Display Device or SwitcherConnect IR Control Devices to the Zone 2 IR Input Select one or all of these methods for audio distribution Step Twelve Plug in AC Power Cords Step Thirteen Insert Batteries in RemoteStep Fourteen Program Sources Into the Remote To program the codes for a source device into the remote To change the device type of a Source Selector To learn individual key codesTo delete a programmed or learned code To rename a key or device Step Fifteen Turn On the AVR 7550HD Initial Setup Using the ON-SCREEN Menu SystemConfigure the AVR 7550HD, Using EzSet/EQ II Technology Select Automatic Setup-EzSet/EQ Set Up Sources Audio and Video Input Selection Channel Inputs You are now ready to begin enjoying your new receiver Volume Control Dolby VolumeDolby Volume Calibration Offset Operation Sleep Timer HeadphonesUsing the Tuner Mute Function XM Radio Operation Video display is in use Internet Radio USB PlaybackTo return to the beginning of the current track, press Using Docking Station Using The Bridge IPod Function Remote Control KeyNetwork Playback Recording IPod Manual Mode TV Out setting to take effectPlay Pause Menu Back/Exit or Left Arrow Select Next Track Next 33 Previous Track Previous I Selecting a Surround Mode Surround Modes Menu Analog Audio Signals Digital Audio SignalsAdvanced Functions Audio Processing and Surround Sound Manual Speaker Setup Dolby Surround SettingsVideo Game Logic 7 Game Step Three Manual Setup Menu Step ONE Determine Speaker CrossoverStep TWO Measure Speaker Distances Number of Speakers Adjust Speaker Distance Menu Adjust Crossover Frequencies MenuSub Mode Step Four Setting Channel Output Levels Manually Video Adjustments Video Modes How to Adjust the Custom Picture Settings System Settings Sharpness Adjustment General AVR Settings Advanced Remote Control FunctionsMenu Appearance System Information Main Menu To end the command sequence, press the OK ButtonActivities Macros Back Light Remote ResetPunch-Through Programming Processor Reset Memory Troubleshooting Guide Symptom Cause Solution Appendix Table A2 Source Setting DefaultsTable A1 Recommended Source Component Connections Table A3 Speaker/Channel Setting Defaults Table A2 Table A4 Delay Setting Defaults Table A5 Source Settings0mS Bridge Table A6 Audio Effects Settings DefaultTable A5 Table A6 Off Black Level Deinterlacing Film Mode Detect 302 Table A7 Video Modes SettingsTable A7 Table A9 Remote Control Codes Table A8 Surround ModesTable A8 Source Input Device Type if changed Table A11 Network Settings Table A10 System SettingsTable A12 Zone 2 Settings Surround Mode Description Incoming Bitstream or Signal Table A13 Surround Modes Table A13 DTS-ES Matrix DTS StereoPresentation DTS Neo6 DTS 2/2/.0 or .1, 3/2/.0 or Subwoofer is used For multichannelAnalog Bypass Remote Control Function List Reference Table A14 Remote Control Function List Radio Table A14 AUX AVR 7550HD Technical Specifications Audio Section