Hearth and Home Technologies SOHO-CE C. Vertical Penetration Framing

Heat & Glo • Soho-CE • 2111-900 Rev. D • 6/07

16

Installing the Ceiling Firestop

• Frame an opening 25.4 cm by 25.4 cm

whenever the system penetrates a ceiling/

ﬂ oor (see Figure 6.3). A steeply slanted

roof may require an enlarged opening

size in order to maintain proper ﬂ ue pipe

clearances.

• Frame the area with the same sized

lumber as used in ceiling/ﬂ oor joist.

• When installing a top ﬂ ue vertical ter-

mination appliance the hole should be

directly above the appliance, unless the

ﬂ ue is offset.

• Do not pack insulation around the ﬂ ue.

Insulation must be kept away from the

pipe.

Installing Attic Shield

Note: An additional ceiling ﬁ restop is not

required if attic shield is used.

• Frame opening for attic shield.

• Attic shield may be installed above or

below ceiling (see Figure 6.4).

• Secure with three fasteners on each

side.

• Fold tabs at top of attic shield in toward

ﬂ ue pipe. Tabs must keep ﬂ ue pipe cen-

tered within shield.

• Field construct additional shield height if

insulation is deeper than height of attic

shield.

C. Vertical Penetration Framing

Figure 6.3

ATTIC

ABOVE

A

B

Figure 6.4 Installing the Attic Shield

A B

SL PIPE 25.4 cm 25.4 cm

3 FASTENERS

PER SIDE

BEND TABS IN

AROUND PIPE

ATTIC SHIELD INSTALLED

BELOW CEILING ATTIC SHIELD INSTALLED

ABOVE CEILING

Fire Hazard

Keep loose materials or blown

insulation from touching the

ﬂ ue pipe.

• Hearth & Home Technologies requires

the use of an attic shield.

WARNING

Contents

Main Model: Soho-CE Installers Guide 0063-06 Congratulations Homeowner Reference Information Table of Contents 1 B. Non-Combustible Materials Speci cation C. Combustible Materials Speci cation A. Appliance Certi cation 2 A. Design and Installation Considerations 2 C. Inspect Appliance and Components B. Tools and Supplies Needed 3 A. Selecting Appliance Location NOTE: For actual appliance dimensions refer to Sec- tion 16. B. Constructing the Appliance Chase C. Clearances 4 A. Flue Termination Minimum Clearances A * 91 cm minimum in snow regions (See Figure 4.4 for speci c clearances) 4 Measure vertical clearances from this surface. Figure 4.2 speci es minimum ue heights for various pitched roofs. V = VENT TERMINAL X Alcove Applications 5 Horizontal B. Use of Elbows A. Flue Table Key C. Measuring Standards 1. Horizontal Termination One Elbow Two Elbows V H D. Flue Diagrams 1. Horizontal Termination - (continued) Three Elbows H V H V 2. Vertical Termination No Elbow Two Elbows V1 = 11.8 m Maximum V 2. Vertical Termination - (continued) Three Elbows V H V INSTALLED HORIZONTALLY H 6 B. Wall Penetration Framing A. Pipe Clearances to Combustibles C. Vertical Penetration Framing 7 A. Securing and Leveling the Appliance 8 8 A. Assembly of Flue Sections B. Installing Firestops and Horizontal Termination Cap * 91 cm minimum in snow regions C. Install Roof Flashing and Vertical Termination Cap Page 9 A. Gas Pressure Requirements 9 B. Gas Connection 10 Heat & Glo Soho-CE 2111-900 Rev. D 6/07 23 A. Electronic Ignition System Wiring Figure 10.1 Electronic Ignition Wiring Diagram 11 11 A. Facing Material B. Mantel Projections 12 12 A. Remove Shipping Materials B. Clean the Appliance Page F. Glass Assembly 13 A. Before Lighting Appliance 13 B. Lighting the Fireplace LIGHTING INSTRUCTIONS CAUTION: WARNING: NOT FOR USE WITH SOLID FUEL C. After Appliance is Lit D. Frequently Asked Questions 14 14 A. Electronic Ignition System 15 15 A. Maintenance Tasks Inspect Maintenance Tasks 16 Appliance Dimensions Table 16 A. Appliance Dimension Diagram SOHO-CE B. Service Parts List SOHO-CE Service Parts SOHO-CE C. Limited Lifetime Warranty LIMITED LIFETIME WARRANTY HEAT & GLO GAS APPLIANCE PRODUCTS