12 Electrical Information
A. Wiring Requirements
NOTICE: This appliance must be installed by a qualified electrician in accordance with the relevant national and local regulations.
•Wire the appliance junction cord to
WARNING! Risk of Shock or Explosion! DO NOT wire 220/240 VAC to the valve or to the appliance wall switch. Incorrect wiring will damage controls.
NOTICE: The mains supply to the appliance must have isolation of a minimum 1/8 in. (3 mm) contact separation in both poles.
WARNING! Risk of Injury! The gas supply shall be shut off prior to disconnecting the electrical power and remov- ing batteries (if installed) before proceeding with any maintenance to the appliance.
B. IntelliFire Plus™ Ignition System Wiring
•Wire the appliance junction cord to
WARNING! Risk of Shock or Explosion! DO NOT wire IPI controlled appliance junction cord to a switched cir- cuit. Incorrect wiring will override IPI safety lockout.
•Refer to Figure 12.1, IntelliFire Plus™ Pilot Ignition (IPI) Wiring Diagram.
•This appliance is equipped with an IntelliFire Plus™ control valve which operates on a 6 volt system.
•For units installed in Australia, the residence’s 220/240 wall outlet to which this appliance’s power cord is con- nected, must be wired to an
•Plug the
C. Optional Accessories Requirements
•This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control.
Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories.
Optional Remote Control Receiver Location
The control module and remote control receiver can be accessed through the air space below the firebox front and the lower access door.
The IPI control module and the remote control receiver are placed on the firebox bottom.
WARNING! Risk of Shock! Label all wires prior to dis- connection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with type 105º C rated wire. Wire must have high temperature insulation.
|
|
|
|
|
|
| 240V FAN |
|
|
|
|
| GAS TUBE |
|
|
|
|
|
|
|
|
|
|
| IGNITOR |
|
|
|
|
| FLAME |
|
|
|
|
|
|
|
| SENSE |
|
|
|
|
|
| 6V DC SUPPLY |
|
|
|
|
|
|
|
| DC REGULATOR |
|
| WHITE | ORANGE |
|
|
|
|
|
| CONTROL MODULE |
|
| ||
|
|
|
| I | AUX300CE MODULE |
| ||
|
|
|
|
|
|
|
| |
|
|
|
| S |
|
| FAN |
|
|
|
|
|
|
|
| AUX 1 AUX 2 | TO JUNCTION |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| BOX |
|
|
|
| 8K1 WIRE |
|
|
|
|
|
|
|
| HARNESS |
|
| TO OPTIONAL |
|
|
|
|
|
|
|
| COMPONENTS |
|
|
| JUNCTION CORD |
|
|
|
|
|
|
|
|
|
| RED |
|
|
|
|
|
|
|
|
|
|
| OPTIONAL ON/OFF |
|
|
| ORANGE | GREEN |
|
|
| WALL SWITCH |
|
|
| BLACK |
|
|
|
| ||
|
| (PILOT) | (MAIN) |
|
|
|
| |
|
|
|
|
|
|
| BATTERY PACK |
|
|
|
|
| BROWN |
|
| 6V DC (C X 4) |
|
|
|
|
|
|
|
|
| |
|
|
|
| GROUND |
|
|
| |
| Figure 12.1 IPI Wiring Diagram /RC300AU |
|
|
|
|
|
| |
| 54 | Heat & Glo • |
| |||||
|
|
| ||||||
