Mantel and Wall Projections | Heat & Glo LifeStyle ESC-42ST instruction

D. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear- ances as speciﬁed. Framing or ﬁnishing material closer than the minimums listed must be constructed entirely of non- combustible materials (i.e., steel studs, concrete board, etc). Failure to comply could cause ﬁre.

Combustible Mantels

12 IN.

MAX.

10 IN.

MIN.

FIREPLACE

OPENING

Figure 5.3 Clearances to mantels or other combustibles above appliance

Non-combustible Mantels

12 IN. MAX.

10 IN.

MIN.

4 IN.

MAX.

NON-COMBUSTIBLE MATERIAL

FIREPLACE

OPENING

Figure 5.4 Clearances to Mantels or other Non-Combustibles Above Appliance

Combustible Mantel Legs or Wall Projections

	FIREPLACE	1 IN. MIN.
	OPENING	1 IN. MIN.
	OPENING
		COMBUSTIBLE
		MATERIAL
		6 IN.
		MAX.
		7 IN.
		6 IN. MIN. FROM
		OPENING
		13 IN. MIN.
		FROM OPENING
		COMBUSTIBLE WALL OR
		MANTEL LEG

Figure 5.5 Clearances to Combustible Mantel Legs or Wall Projections.

Non-Combustible Mantel Legs or Wall Projections

FIREPLACE
OPENING	1 IN. MIN.
4 IN. MAX.	NON-COMBUSTIBLE
	MANTEL LEG
	13 IN. MIN.
	NON-COMBUSTIBLE WALL

Figure 5.6 Clearances to Non-Combustible Mantel Legs or Wall Projections.

Heat & Glo • ESC-42ST • 2146-900 Rev. o • 5/12

21

Image 21

Heat & Glo LifeStyle ESC-42ST owner manual Mantel and Wall Projections, MIN MAX NON-COMBUSTIBLE Material Fireplace Opening

Contents

Model ESC-42ST What to do if you smell gasDo Discardnot Homeowner Reference Information Congratulations User Guide Table of Contents Appliance Setup TroubleshootingReference Materials Limited Lifetime Warranty Warranty Conditions Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide Detectors Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Remote Control Fixed Glass AssemblyClear Space Decorative Doors and Fronts Module Reset IPI Battery Tray/Battery InstallationNine Hour Safety Shutdown Feature Control Module Operation Final inspection by Lighting Instructions IPI After Fireplace is Lit Frequently Asked Questions Maintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Exterior of Installed Glass Only Doors, Surrounds, Fronts Glass Cleaning Exterior and Interior of Installed Glass Maintenance Tasks-Qualiﬁed Service TechnicianGasket Seal and Glass Assembly Inspection Logs Frequency As needed Light Bulb Maintenance Typical Appliance System Getting Started Design and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Framing and Clearances Selecting Appliance LocationBoard not Shown Attached to Minimum Framing Dimensions Constructing the Appliance ChaseClearances MIN MAX NON-COMBUSTIBLE Material Fireplace Opening Mantel and Wall Projections Combustible Material Hearth Extension Vent Termination Minimum Clearances Termination Locations Inches U.S.A Covered Alcove Applications Approved Pipe Vent Information and DiagramsVent Table Key Use of Elbows Vent Diagrams Top Vent Horizontal Termination One Elbow Top Vent Horizontal TerminationTwo Elbows H1+ H2 Top Vent Horizontal Termination Three Elbows 12 ft V1 + V2 + H1 = 50 ft 15.2 m Max Ht Max Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Non-Combustible Wall Penetration Pipe DVP Install the Ceiling Firestop Install Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Top Vent Appliance Preparation Appliance Package Identiﬁcation Securing and Leveling the Appliance Attach Vent to the Firebox Assembly Installing Vent PipeAssemble Vent Sections Assemble Pipe Sections Secure the Vent Sections Assemble Slip Sections Disassemble Vent Sections 10 Rotate Seams for Disassembly Assemble and Install Storm Collar Install Metal Roof Flashing Install Vertical Termination Cap Install Horizontal Termination CapHeat Shield Requirements for Horizontal Termination Fuel Conversion Gas InformationGas Pressure Gas Connection IntelliFire Plus Ignition System Wiring Wiring RequirementsElectrical Service and Repair Junction Box Installation Electrical Information IPI Wiring Diagram Finishing Doors Facing Material Model Description Elevated Appliance Dimension Elevated Hearth SystemsESC-42ST TAB Appliance Setup Accessories Clean the ApplianceInstalling the Optional Heat-ZoneGas Kit Remove the Shipping Materials Ember Lights Install Light BulbsAccent Lights Screws Notch Install RefractoryFlange Outer Firebox Flange Refractory Clips Mystic Ember Placement Install Teco-Sil Glass Ember Rock LOG Placement Instructions Grate Tine Grate BAR  4 Install Outer Refractory Panels Ember/Mineral Wool Placement Install Trim and/or Surround Install MeshAir Shutter Setting Air Shutter Settings Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System Troubleshooting Reference Materials Appliance Dimension Diagram DVP-AS2 Vent Components Diagrams DVP-TRAP DVP-TRAP1 DVP-TRAP2 DVP-TRAPK1 DVP-TRAPK2 RF6M RF12M Description Part Number Optional Wire Harness Service Parts Refractory Assembly Log Set Assembly Service Parts List At DepotDescription Comments Part Number Stocked Pre SN #28 IPI Valve Assembly Post SN Contact Information