GAS Line Electrical Access | Heat & Glo LifeStyle SL-750TRS-IPI-D

			25-3/4
			[654 ]
			12-7/8		1/2 [13]
			12-7/8
			[327]
		15-7/8					16-1/4
		[403]			8-13/16		[413]
					[224]
			ø	6-5/8 [168.3]				ø 8 [168.3]
	35-7/16			5-1/2
	35-7/16			[140 ]		3-1/2
	[900.1]	2-1/8	32-1/8	[140 ]				32-9/16
	[900.1]	2-1/8	32-1/8					32-9/16
		[54]	[816 ]			[90]		[827]
	GAS LINE							ELECTRICAL
	ACCESS	6	31-1/8		6-7/8			ACCESS
		6	[ 791]		6-7/8
		[152]			[174]
			36
			[914]
			TOP STANDOFFS
								VENT COLLARS
			HOOD
			CERAMIC
			FIBER PAD
			RATING PLATES
			& LABELS
	GAS LINE		GAS	BOTTOM GRILLE				ELECTRICAL
	GAS LINE		GAS	COVER				ELECTRICAL
	ACCESS	CONTROLS		COVER				ACCESS
	ACCESS	CONTROLS						ACCESS
	Figure 2. Diagram of the SL-550TRS-IPI-D
	16	Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Image 16

Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual GAS Line Electrical Access

Contents

Installation and Operation SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Safety and Warning Information Table of Contents Log Set Assembly SL-350TRS-C NG, LP Service Parts List SL-350TRS-C Valve Assembly Standing Pilot Ignition SL-550TRS-IPI-D SL-550TRS-IPI-D Log Set Assembly Part number list on following SL-750TRS-IPI-D Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D Intermittent Pilot Ignition Valve Assembly High Altitude Installations Installation CodesAppliance Certification Certification Vent Directly BELOW. Keep Clear of ALL OB- Structions Requirements for the Commonwealth of MassachusettsManufacturer Requirements Introducing the Heat & Glo Gas Appliances Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Access Diagram of the SL-350TRS-C Locating the Appliance Constructing the Appliance ChaseClearance Requirements Framing Dimensions Framing the Appliance 34.93mm AT Each Joint 47 3/4 Installing the Vent System System ConfigurationIdentifying Vent Components SL D-SERIES Components in ANY Vent Straight UP Vertical Venting Flex VentWith TWO 900 Elbows Use DVP-Series Components only Venting with One 90 Elbow Use SL D-Series components only Venting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting Only SL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting Collars DVP, SL-D and SL-Flex Series Venting Hole and Vent Pipe Vent Termination SL-Series Venting OnlyFor DVP Venting Only For All Venting Alcove Applications Vent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Appliance Gas Control SystemsStanding Pilot Ignition System Millivolt System Gas Pressure Requirements Gas Supply LinePressure Natural Gas Propane Wiring the Appliance For Standing Pilot Ignition Wiring Appliance RequirementsOptional Accessories Wall Switch Operation using Battery Power Intermittent Pilot Ignition IPI Wiring Diagram Finishing NER Installing the Trim Shutter SettingsGlass Specifications Positioning the Logs After the Installation Double-check for faulty componentsBefore Lighting the Appliance Lighting the Appliance Appliance Maintenance Important Turn OFF the GAS Before Servicing Your Appliance