34.93mm AT Each Joint | Heat & Glo LifeStyle SL-750TRS-IPI-D

4

6

12

DVP4

DVP6

DVP12

14-1/4

	12-3/16	2
	MAX.	2
	MAX.	MIN.
		MIN.
		24
	DVP12A	36

48

9-7/8	DVP24
	DVP24
	45.0O

10-1/4

DVP45

DVP36

11-1/4

7-1/4

1-1/4 TYP

DVP48

8-9/16

1/2 TYP

12-9/16

DVP90ST

NOTE: PIPES OVERLAP 1-1/4 INCHES

(34.93mm) AT EACH JOINT.

Figure 6. DVP-Series Direct Vent Component Specifications (5-inch inner pipe / 8-inch outer pipe)

20	Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Image 20

Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual 34.93mm AT Each Joint

Contents

Installation and Operation SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Safety and Warning Information Table of Contents Log Set Assembly SL-350TRS-C NG, LP Service Parts List SL-350TRS-C Valve Assembly Standing Pilot Ignition SL-550TRS-IPI-D SL-550TRS-IPI-D Log Set Assembly Part number list on following SL-750TRS-IPI-D Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D Intermittent Pilot Ignition Valve Assembly High Altitude Installations Installation CodesAppliance Certification Certification Manufacturer Requirements Requirements for the Commonwealth of MassachusettsVent Directly BELOW. Keep Clear of ALL OB- Structions ANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Heat & Glo Gas Appliances Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Access Diagram of the SL-350TRS-C Clearance Requirements Constructing the Appliance ChaseLocating the Appliance Framing Dimensions Framing the Appliance 34.93mm AT Each Joint 47 3/4 Installing the Vent System System ConfigurationIdentifying Vent Components SL D-SERIES Components in ANY Vent With TWO 900 Elbows Flex VentStraight UP Vertical Venting Use DVP-Series Components only Venting with One 90 Elbow Use SL D-Series components only Venting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting Only SL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting Collars DVP, SL-D and SL-Flex Series Venting Hole and Vent Pipe Vent Termination SL-Series Venting OnlyFor DVP Venting Only For All Venting Alcove Applications Vent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Appliance Gas Control SystemsStanding Pilot Ignition System Millivolt System Pressure Natural Gas Propane Gas Supply LineGas Pressure Requirements Wiring the Appliance For Standing Pilot Ignition Wiring Appliance RequirementsOptional Accessories Wall Switch Operation using Battery Power Intermittent Pilot Ignition IPI Wiring Diagram Finishing NER Installing the Trim Shutter SettingsGlass Specifications Positioning the Logs After the Installation Double-check for faulty componentsBefore Lighting the Appliance Lighting the Appliance Appliance Maintenance Important Turn OFF the GAS Before Servicing Your Appliance