Manuals / Heat & Glo LifeStyle / Household Appliance / Electric Heater

Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual SL-550TRS-IPI-D, Service Parts

Models: SL-750TRS-IPI-D

1 45

Page 7

Service Parts	SL-550TRS-IPI-D

(NG, LP) Exploded Parts Diagram	Beginning Manufacturing Date: 4-04
	Ending Manufacturing Date: ______

4

13	7 Log Set Assembly	15	1
			1
2
2
	12		9
	12
3	11		10
	11

		8

Part number list on following page.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Page 7

Image 7

Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual SL-550TRS-IPI-D, Service Parts

Contents

SL-350TRS-C Models SL-750TRS-IPI-D SL-550TRS-IPI-DWhat to do if you smell gas PROHIBITED SAFETY AND WARNING INFORMATIONSection 3 Installing the Appliance TABLE OF CONTENTSSection 2 Getting Started NG, LP Exploded Parts Diagram Service PartsSL-350TRS-C 7 Log Set AssemblySL-350TRS-C NG, LP Service Parts ListStanding Pilot Ignition Service PartsValve Assembly SL-350TRS-CService Parts SL-550TRS-IPI-DNG, LP Service Parts List SL-550TRS-IPI-DACCESSORIES NG, LP Exploded Parts Diagram SL-750TRS-IPI-DService Parts 7Log Set AssemblyNG, LP Service Parts List SL-750TRS-IPI-DACCESSORIES Intermittent Pilot Ignition Valve Assembly Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-DAppliance Certification High Altitude InstallationsInstallation Codes 1Approvals and CodesInspection Installation of Carbon Monoxide DetectorsApproved Carbon Monoxide Detectors SignageANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Pre-installPreparation2Getting Started Introducing the Heat & Glo Gas AppliancesFigure 1. Diagram of the SL-750TRS-IPI-D Figure 2. Diagram of the SL-550TRS-IPI-D 22-3/4577 Clearance Requirements 3Installing the ApplianceConstructing the Appliance Chase Step 1. Locating the ApplianceFigure 5. Framing Dimensions Step 2. Framing the Appliance34.93mm AT EACH JOINT NOTE PIPES OVERLAP 1-1/4INCHES47 3/4 NOTE PIPES OVERLAP 1-3/8INCHES34.93mm AT EACH JOINT 4-inchinner pipe / 6 5/8-inchouter pipeusing 45 elbows Step 3. Installing the Vent SystemIdentifying Vent Components SYSTEM CONFIGURATIONStraight up Vertical Venting Flex VentSTRAIGHT UP VERTICAL VENTING Use SL D-Seriescomponents only FigureUse SL D-Seriescomponents only Use DVP-Seriescomponents only Figure 12. Venting with One 90 ElbowH + H1 Use DVP-Seriescomponents only Figure 14. Venting with Two 90 ElbowsNATURAL GAS Use SL D-Seriescomponents onlyFigure 15. Venting with Two 90 Elbows VENTING WITH TWO 2 90o ELBOWSNATURAL GAS Use SL D-Seriescomponents onlyFigure 16. Venting with Two 90 Elbows VENTING WITH TWO 2 90o ELBOWSH + H1 + H2 Use DVP-Seriescomponents onlyFigure 17. Venting with Three 90 elbows H + H1NATURAL GAS Use SL D-Seriescomponents onlyFigure 18. Venting with three 90 elbows VENTING WITH THREE 3 90o ELBOWSNATURAL GAS Use SL D-Seriescomponents onlyFigure 19. Venting with three 90 elbows VENTING WITH THREE 3 90o ELBOWSVENTING WITH FOUR 4 90 ELBOWS H1Use SL D-Seriescomponents only Figure 20. Venting with Four 90 elbows3. Install Support Brackets DVP Series Venting OnlyGo to Step 4 Install Firestops B. Installing Vent ComponentsFigure 23. Installing Support Brackets SL-Dand SL-FlexSeries Venting OnlyGo to Step 4 Install Firestops 3. Install Support BracketsFigure 26. Hole & New Framing Members DVP, SL-Dand SL-FlexSeries VentingSTEP 4. Install Firestops Figure 24. Hole and Vent PipeFor All Venting C.Vent TerminationSL-SeriesVenting Only For DVP Venting Only= VENT TERMINAL = AREA WHERE TERMINAL IS NOT PERMITTEDAlcove Applications Figure 30. Vent Termination Minimum ClearancesMark the roof hole accordingly WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUEL Step 5. The Gas Control SystemsFigure 32. Proper Positioning, Leveling, and Securing of a AppliancePressure Step 6. The Gas Supply LineStep 7. Gas Pressure Requirements Figure 34. Gas Supply LineWall Switch Step 8. Wiring the ApplianceFor Standing Pilot Ignition Wiring Optional AccessoriesWall Switch For Intermittent Pilot Ignition IPI WiringOperation using Battery Power Optional AccessoriesFigure 39. Sealant Material Hearth Extensions Step 9. FinishingPositioning the Logs Installing the TrimShutter Settings GLASS SPECIFICATIONSReview safety warnings and cautions After the InstallationStep 11. Before Lighting the Appliance Step 12. Lighting the ApplianceCleaning Glass Door Appliance Maintenance4Maintaining and Servicing Your Appliance Cleaning Flame Sensor Rod IPI Systems