Heat & Glo LifeStyle SL-750TRS-IPI-D manual

		30-3/4
		[781]		1/2
		15-3/8		1/2
		15-3/8		[13]
		[391]
		15-7/8				16-1/4
		15-7/8			8-3/4	[413]
		[403]				[413]
		[403]
					[222]
			ø 6-5/8	[168.3]
40						37-7/8
[1016]						37-7/8
[1016]	2-1/4 35-5/8			5-1/2		[962]
	2-1/4 35-5/8			5-1/2	3-9/16	[962]
	[57]	[905]		[140]	3-9/16
					[90]
		36-1/8				ELECTRICAL
		[918]				ELECTRICAL
GASS LINE	6	[918]			6-7/8	ACCESS
GASS LINE	6	41			6-7/8	ACCESS
ACCESS	[152]	[1041.4]			[175]
		TOP STANDOFFS
						VENT COLLARS
		HOOD
		CERAMIC
		FIBER PAD
		RATING PLATES
		& LABELS
GAS LINE		GAS	BOTTOM GRILLE			ELECTRICAL
GAS LINE		GAS	COVER			ELECTRICAL
ACCESS		CONTROLS	COVER			ACCESS
ACCESS		CONTROLS				ACCESS
Figure 1. Diagram of the SL-750TRS-IPI-D
	Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06					15

Image 15

Heat & Glo LifeStyle owner manual Diagram of the SL-750TRS-IPI-D

Contents

SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Installation and Operation Safety and Warning Information Table of Contents SL-350TRS-C Log Set Assembly SL-350TRS-C NG, LP Service Parts List Standing Pilot Ignition Valve Assembly SL-550TRS-IPI-D SL-550TRS-IPI-D Part number list on following Log Set Assembly SL-750TRS-IPI-D Intermittent Pilot Ignition Valve Assembly Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D Certification High Altitude InstallationsInstallation Codes Appliance Certification Requirements for the Commonwealth of Massachusetts Vent Directly BELOW. Keep Clear of ALL OB- StructionsManufacturer Requirements Pre-install Preparation Introducing the Heat & Glo Gas AppliancesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Diagram of the SL-350TRS-C Access Constructing the Appliance Chase Locating the ApplianceClearance Requirements Framing the Appliance Framing Dimensions 34.93mm AT Each Joint 47 3/4 SL D-SERIES Components in ANY Vent Installing the Vent SystemSystem Configuration Identifying Vent Components Flex Vent Straight UP Vertical VentingWith TWO 900 Elbows Venting with One 90 Elbow Use SL D-Series components only Use DVP-Series Components only Venting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows DVP Series Venting Only Go to Install Firestops Attach the First Vent Component to the Starting Collars SL-D and SL-Flex Series Venting Only Hole and Vent Pipe DVP, SL-D and SL-Flex Series Venting For All Venting Vent TerminationSL-Series Venting Only For DVP Venting Only Vent Termination Minimum Clearances Alcove Applications Minimum Height from Roof to Lowest Discharge Opening Millivolt System Positioning, Leveling, and Securing the ApplianceGas Control Systems Standing Pilot Ignition System Gas Supply Line Gas Pressure RequirementsPressure Natural Gas Propane Wall Switch Wiring the ApplianceFor Standing Pilot Ignition Wiring Appliance Requirements Optional Accessories Intermittent Pilot Ignition IPI Wiring Diagram Operation using Battery Power NER Finishing Positioning the Logs Installing the TrimShutter Settings Glass Specifications Lighting the Appliance After the InstallationDouble-check for faulty components Before Lighting the Appliance Important Turn OFF the GAS Before Servicing Your Appliance Appliance Maintenance