Manuals / Heat & Glo LifeStyle / Household Appliance / Electric Heater

Heat & Glo LifeStyle SL-750TRS-IPI-D Service Parts, 7Log Set Assembly, Ending Manufacturing Date

Models: SL-750TRS-IPI-D

1 45

Page 9

Service Parts	SL-750TRS-IPI-D

(NG, LP) Exploded Parts Diagram	Beginning Manufacturing Date: 4-04
	Ending Manufacturing Date: ______

6

2	13	15	1

7Log Set Assembly

3
12		9
	11	10
Part number list on following page.		10
Part number list on following page.	8
	8

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

Page 9

Image 9

Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual Service Parts, 7Log Set Assembly, Part number list on following page

Contents

Models SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-CWhat to do if you smell gas PROHIBITED SAFETY AND WARNING INFORMATIONTABLE OF CONTENTS Section 3 Installing the ApplianceSection 2 Getting Started SL-350TRS-C Service Parts7 Log Set Assembly NG, LP Exploded Parts DiagramSL-350TRS-C NG, LP Service Parts ListValve Assembly Service PartsSL-350TRS-C Standing Pilot IgnitionService Parts SL-550TRS-IPI-DSL-550TRS-IPI-D NG, LP Service Parts ListACCESSORIES Service Parts SL-750TRS-IPI-D7Log Set Assembly NG, LP Exploded Parts DiagramSL-750TRS-IPI-D NG, LP Service Parts ListACCESSORIES Intermittent Pilot Ignition Valve Assembly Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-DInstallation Codes High Altitude Installations1Approvals and Codes Appliance CertificationApproved Carbon Monoxide Detectors Installation of Carbon Monoxide DetectorsSignage Inspection2Getting Started Pre-installPreparationIntroducing the Heat & Glo Gas Appliances ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the SL-750TRS-IPI-D Figure 2. Diagram of the SL-550TRS-IPI-D 22-3/4577 Constructing the Appliance Chase 3Installing the ApplianceStep 1. Locating the Appliance Clearance RequirementsFigure 5. Framing Dimensions Step 2. Framing the Appliance34.93mm AT EACH JOINT NOTE PIPES OVERLAP 1-1/4INCHES34.93mm AT EACH JOINT NOTE PIPES OVERLAP 1-3/8INCHES4-inchinner pipe / 6 5/8-inchouter pipe 47 3/4Identifying Vent Components Step 3. Installing the Vent SystemSYSTEM CONFIGURATION using 45 elbowsSTRAIGHT UP VERTICAL VENTING Flex VentUse SL D-Seriescomponents only Figure Straight up Vertical Ventingcomponents only Use DVP-SeriesFigure 12. Venting with One 90 Elbow Use SL D-Seriescomponents onlycomponents only Use DVP-SeriesFigure 14. Venting with Two 90 Elbows H + H1Figure 15. Venting with Two 90 Elbows Use SL D-Seriescomponents onlyVENTING WITH TWO 2 90o ELBOWS NATURAL GASFigure 16. Venting with Two 90 Elbows Use SL D-Seriescomponents onlyVENTING WITH TWO 2 90o ELBOWS NATURAL GASFigure 17. Venting with Three 90 elbows Use DVP-Seriescomponents onlyH + H1 H + H1 + H2Figure 18. Venting with three 90 elbows Use SL D-Seriescomponents onlyVENTING WITH THREE 3 90o ELBOWS NATURAL GASFigure 19. Venting with three 90 elbows Use SL D-Seriescomponents onlyVENTING WITH THREE 3 90o ELBOWS NATURAL GASUse SL D-Seriescomponents only H1Figure 20. Venting with Four 90 elbows VENTING WITH FOUR 4 90 ELBOWSGo to Step 4 Install Firestops DVP Series Venting OnlyB. Installing Vent Components 3. Install Support BracketsGo to Step 4 Install Firestops SL-Dand SL-FlexSeries Venting Only3. Install Support Brackets Figure 23. Installing Support BracketsSTEP 4. Install Firestops DVP, SL-Dand SL-FlexSeries VentingFigure 24. Hole and Vent Pipe Figure 26. Hole & New Framing MembersSL-SeriesVenting Only C.Vent TerminationFor DVP Venting Only For All VentingAlcove Applications = AREA WHERE TERMINAL IS NOT PERMITTEDFigure 30. Vent Termination Minimum Clearances = VENT TERMINALMark the roof hole accordingly Figure 32. Proper Positioning, Leveling, and Step 5. The Gas Control SystemsSecuring of a Appliance WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUELStep 7. Gas Pressure Requirements Step 6. The Gas Supply LineFigure 34. Gas Supply Line PressureFor Standing Pilot Ignition Wiring Step 8. Wiring the ApplianceOptional Accessories Wall SwitchOperation using Battery Power For Intermittent Pilot Ignition IPI WiringOptional Accessories Wall SwitchFigure 39. Sealant Material Hearth Extensions Step 9. FinishingShutter Settings Installing the TrimGLASS SPECIFICATIONS Positioning the LogsStep 11. Before Lighting the Appliance After the InstallationStep 12. Lighting the Appliance Review safety warnings and cautions4Maintaining and Servicing Your Appliance Appliance MaintenanceCleaning Flame Sensor Rod IPI Systems Cleaning Glass Door

SL-750TRS-IPI-D

6

7Log Set Assembly

Part number list on following page.