Access | Heat & Glo LifeStyle SL-750TRS-IPI-D specification

				22-3/4 [577]
		11-3/8 [289]		1/2[13]
		11-3/8 [289]
		15-7/8	[402]		16-1/4
		15-7/8	[402]	8-3/4 [413]
				8-3/4 [413]
				[223]			ø8 [203]
							ø8 [203]
		ø 6-5/8 [168.3]
34-1/2		2-1/8 30-1/2		15-1/4	29	3-1/2	30-5/8
[876]		2-1/8 30-1/2		[388]	29	[90]	[777]
		[55]	[776]		[737]		21-1/4
							[540]
GAS LINE				28-1/8	6-7/8		ELECTRICAL
ACCESS			6	[714]	6-7/8		ACCESS
			6	33	[174]
		[153]		33	[174]
		[153]		[836]
				[836]
				TOP STANDOFFS
							VENT COLLARS
				HOOD
				CERAMIC
				FIBER PAD
				RATING PLATES
				& LABELS
GAS LINE			GAS	BOTTOM GRILLE			ELECTRICAL
GAS LINE			GAS	COVER			ELECTRICAL
ACCESS			CONTROLS	COVER			ACCESS
ACCESS			CONTROLS				ACCESS
Figure 3.	Diagram of the SL-350TRS-C
		Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06					17

Image 17

Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual Access, Diagram of the SL-350TRS-C

Contents

SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Installation and Operation Safety and Warning Information Table of Contents SL-350TRS-C Log Set Assembly SL-350TRS-C NG, LP Service Parts List Standing Pilot Ignition Valve Assembly SL-550TRS-IPI-D SL-550TRS-IPI-D Part number list on following Log Set Assembly SL-750TRS-IPI-D Intermittent Pilot Ignition Valve Assembly Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D Installation Codes High Altitude InstallationsAppliance Certification Certification Manufacturer Requirements Requirements for the Commonwealth of MassachusettsVent Directly BELOW. Keep Clear of ALL OB- Structions ANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Heat & Glo Gas Appliances Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Diagram of the SL-350TRS-C Access Clearance Requirements Constructing the Appliance ChaseLocating the Appliance Framing the Appliance Framing Dimensions 34.93mm AT Each Joint 47 3/4 System Configuration Installing the Vent SystemIdentifying Vent Components SL D-SERIES Components in ANY Vent With TWO 900 Elbows Flex VentStraight UP Vertical Venting Venting with One 90 Elbow Use SL D-Series components only Use DVP-Series Components only Venting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows DVP Series Venting Only Go to Install Firestops Attach the First Vent Component to the Starting Collars SL-D and SL-Flex Series Venting Only Hole and Vent Pipe DVP, SL-D and SL-Flex Series Venting SL-Series Venting Only Vent TerminationFor DVP Venting Only For All Venting Vent Termination Minimum Clearances Alcove Applications Minimum Height from Roof to Lowest Discharge Opening Gas Control Systems Positioning, Leveling, and Securing the ApplianceStanding Pilot Ignition System Millivolt System Pressure Natural Gas Propane Gas Supply LineGas Pressure Requirements For Standing Pilot Ignition Wiring Appliance Requirements Wiring the ApplianceOptional Accessories Wall Switch Intermittent Pilot Ignition IPI Wiring Diagram Operation using Battery Power NER Finishing Shutter Settings Installing the TrimGlass Specifications Positioning the Logs Double-check for faulty components After the InstallationBefore Lighting the Appliance Lighting the Appliance Important Turn OFF the GAS Before Servicing Your Appliance Appliance Maintenance