Table of Contents | Heat & Glo LifeStyle SL-750TRS-IPI-D specs

TABLE OF CONTENTS
Safety and Warning Information		2
ÎService Parts Lists		4
Section 1: Approvals and Codes		12
Appliance Certification		12
Installation Codes		12
High Altitude Installations		12
Î Requirements for the Commonwealth of Massachusetts		13
Section 2: Getting Started		14
Introducing the Heat & Glo Gas Appliances		14
Pre-installation Preparation		14
Section 3: Installing the Appliance		18
Constructing the Appliance Chase		18
Step 1	Locating the Appliance	18
Step 2	Framing the Appliance	19
Step 3	Installing the Vent System	22
	A. Vent System Approvals	22
	B. Installing Vent Components	32
	C. Vent Termination	35
Step 4	Positioning, Leveling, and
	Securing the Appliance	38
Step 5	The Gas Control Systems	38
Step 6	The Gas Supply Line	39
Step 7	Gas Pressure Requirements	39
Step 8	Wiring the Appliance	40
Step 9	Finishing	42
Step 10	Installing Trim, Logs, and Ember Material	43
	Installing the Trim	43
	Positioning the Logs	43
	Shutter Settings	43
	Placing the Ember Material	43
	Glass Specifications	43
Step 11 Before Lighting the Appliance		44
Step 12	Lighting the Appliance	44
After the Installation		44
Section 4: Maintaining and Servicing Your Appliance		45
	Î= Contains updated information.

Heat & Glo • SL-350TRS-C, SL-550/750TRS-IPI-D • 2065-985 Rev. J • 5/06

3

Image 3

Heat & Glo LifeStyle SL-750TRS-IPI-D owner manual Table of Contents

Contents

SL-750TRS-IPI-D SL-550TRS-IPI-D SL-350TRS-C Installation and Operation Safety and Warning Information Table of Contents SL-350TRS-C Log Set Assembly SL-350TRS-C NG, LP Service Parts List Standing Pilot Ignition Valve Assembly SL-550TRS-IPI-D SL-550TRS-IPI-D Part number list on following Log Set Assembly SL-750TRS-IPI-D Intermittent Pilot Ignition Valve Assembly Service Parts SL-750TRS-IPI-D, SL-550TRS-IPI-D Certification High Altitude InstallationsInstallation Codes Appliance Certification Requirements for the Commonwealth of Massachusetts Vent Directly BELOW. Keep Clear of ALL OB- StructionsManufacturer Requirements Pre-install Preparation Introducing the Heat & Glo Gas AppliancesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the SL-750TRS-IPI-D GAS Line Electrical Access Diagram of the SL-350TRS-C Access Constructing the Appliance Chase Locating the ApplianceClearance Requirements Framing the Appliance Framing Dimensions 34.93mm AT Each Joint 47 3/4 SL D-SERIES Components in ANY Vent Installing the Vent SystemSystem Configuration Identifying Vent Components Flex Vent Straight UP Vertical VentingWith TWO 900 Elbows Venting with One 90 Elbow Use SL D-Series components only Use DVP-Series Components only Venting with Two 90 Elbows Venting with TWO 2 90 o Elbows MAX. = 16 FT 4.8m + V 1 + H MAX. = 40 FT 12.2m Venting with Three 90 elbows Venting with Three 3 90 o Elbows + H 1 MAX. = 16 FT 4.8m + V 1 + H + H MAX. = 40 FT 12.2m Venting with Four 90 elbows DVP Series Venting Only Go to Install Firestops Attach the First Vent Component to the Starting Collars SL-D and SL-Flex Series Venting Only Hole and Vent Pipe DVP, SL-D and SL-Flex Series Venting For All Venting Vent TerminationSL-Series Venting Only For DVP Venting Only Vent Termination Minimum Clearances Alcove Applications Minimum Height from Roof to Lowest Discharge Opening Millivolt System Positioning, Leveling, and Securing the ApplianceGas Control Systems Standing Pilot Ignition System Gas Supply Line Gas Pressure RequirementsPressure Natural Gas Propane Wall Switch Wiring the ApplianceFor Standing Pilot Ignition Wiring Appliance Requirements Optional Accessories Intermittent Pilot Ignition IPI Wiring Diagram Operation using Battery Power NER Finishing Positioning the Logs Installing the TrimShutter Settings Glass Specifications Lighting the Appliance After the InstallationDouble-check for faulty components Before Lighting the Appliance Important Turn OFF the GAS Before Servicing Your Appliance Appliance Maintenance