|
|
|
|
|
| Part names |
|
|
|
|
|
| Power switch (17) |
|
|
|
|
|
| AC inlet (14) |
Ports (See below.) |
|
|
|
|
| Elevator button (9) |
|
|
|
|
| Elevator foot (9) | |
|
|
|
|
|
| |
|
| Vent (7) | ||||
|
|
|
|
|
| |
CONTROL port (12) | Restart switch (*) (48) | |||||
|
| RGB IN1 port (12) | ||||
AUDIO IN2 L/R port (13) |
|
|
|
| ||
|
|
|
| RGB IN2 /RGB OUT port (12) | ||
(In the default setting, the |
|
|
|
| ||
AUDIO IN2 L/R port is the audio |
|
|
| (Use the RGB IN OUT switch to select | ||
port for the VIDEO, |
|
|
| RGB IN2 or RGB OUT for this port.) | ||
and COMPONENT VIDEO |
|
|
|
| RGB IN2 port: Inputs the RGB signal from | |
ports, however it is possible to |
|
|
| a PC. | ||
change the settings. 34) |
|
|
|
| RGB OUT port: When connected to a | |
|
|
|
|
|
| monitor, outputs the signal input via RGB |
COMPONENT |
|
|
|
|
| IN1. |
Y | R |
|
|
|
| |
VIDEO ports (13) |
|
|
|
| ||
|
| AUDIO IN2 |
|
| USB port (12) | |
Y |
|
|
|
|
| |
|
|
| CONTROL |
| RGB IN1 | |
CB/PB | CB/PB |
|
|
| ||
| AUDIO OUT |
| RGB OUT | |||
CR/PR |
|
|
|
|
| RGB IN2 USB |
| L | AUDIO IN1 |
| K | ||
CR/PR |
|
| ||||
VIDEO port (13) |
|
|
|
|
| |
VIDEO |
| LINK | LAN |
| ||
ACT |
| |||||
|
|
|
| |||
|
|
|
|
| ||
|
|
|
|
| Ports | |
AUDIO IN1 port (12) |
|
|
|
| RGB IN OUT switch (12) | |
|
|
|
| Use this button to select either RGB IN2 | ||
(In the default setting, the AUDIO |
|
| ||||
|
| or RGB OUT for the corresponding port. | ||||
IN1 port is the audio port for the |
|
| ||||
|
| When this switch is not pushed in, RGB | ||||
RGB IN1 and RGB IN2 ports, |
|
|
| |||
|
|
| IN2 is selected. | |||
however, it is possible to change |
|
| ||||
|
| When this switch is pushed in, RGB OUT | ||||
the settings. 34) |
|
|
|
|
| |
|
|
|
|
| is selected. | |
|
|
|
|
|
| |
|
|
| LAN Port (12) | |||
|
|
| Used for Ethernet input/output. | |||
|
|
| This port is used when utilizing network functions. | |||
NOTE (*) About Restart switch: This projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly and the microprocessor will need to be reset. In such a case, please push the Restart switch by using a cocktail stick or similar, and before turning on again, make the projector cool down at least 10 minutes without operating. Only push the Restart switch in these exceptional instances.
5
