Regarding the indicator lamps, Has been detected | Hitachi EDPJ32

Troubleshooting

Regarding the indicator lamps

Lighting and ﬂashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please follow the instructions within the table. If the same indication is displayed after the remedy, or if an indication other than the following is displayed, please contact your dealer or service company.

	POWER	LAMP	TEMP	Description
	indicator	indicator	indicator	Description
	indicator	indicator	indicator

	Lighting	Turned	Turned	The projector is in a standby state.
	In Orange	off	off	Please refer to the section “Power On/Off”.(19)
	Blinking	Turned	Turned	The projector is warming up.
	In Green	off	off	Please wait.
	Lighting	Turned	Turned	The projector is in an on state.
	In Green	off	off	Ordinary operations may be performed.
	Blinking	Turned	Turned	The projector is cooling down.
	In Orange	off	off	Please wait.
				The projector is cooling down. A certain error
	Blinking	(discre-	(discre-	has been detected.
	In Red	tionary)	tionary)	Please wait until the POWER indicator ﬁnishes
	In Red	tionary)	tionary)	blinking, and then perform the proper measure,
				blinking, and then perform the proper measure,
				referring to the item descriptions below.
				The lamp does not light, and there is a
				possibility that interior portion has become
				heated.
				Please turn the power off, and allow the projector to
	Blinking			cool down at least 20 minutes. After the projector has
	In Red	Lighting	Turned	sufﬁciently cooled down, please make conﬁrmation of
	or	Lighting	Turned	the following items, and then turn the power on again.
	or	In Red	off	the following items, and then turn the power on again.
	Lighting	In Red	off	• Is there blockage of the air passage aperture?
	Lighting			• Is there blockage of the air passage aperture?
	In Red			• Is the air ﬁlter dirty?
				• Does the peripheral temperature exceed 35°C?
				If the same indication is displayed after the remedy,
				please change the lamp referring to the section “Lamp”
				(48, 49).
				The lamp cover has not been properly ﬁxed.
				Please turn the power off, and allow the projector to
	Blinking			cool down at least 45 minutes. After the projector has
	In Red	Blinking	Turned	sufﬁciently cooled down, please make conﬁrmation
	or	Blinking	Turned	of the attachment state of the lamp cover. After
	or	In Red	off	of the attachment state of the lamp cover. After
	Lighting	In Red	off	performing any needed maintenance, turn the power
	Lighting			performing any needed maintenance, turn the power
	In Red			on again. If the same indication is displayed after
				the remedy, please contact your dealer or service
				company.

54

Image 54

Hitachi EDPJ32 Regarding the indicator lamps, The projector is in a standby state, The projector is in an on state, heated

Contents

EDPJ32 Thank you for purchasing this projectorTrademark acknowledgment User’s Manual - Operating Guide Before use ContentPower on/off Preparations Troubleshooting Multifunctional settingsMaintenance Warranty and after-service Projector features Before useAbout this manual About contents of package Part names Projector47, 48 Remote control Control buttons Preparations Fastening the lens cover About the ﬁlter cover bottom-up use TabsFilter cover’s knob Filter cover for bottom-up use with an air ﬁlter When put on a table When suspended from the ceiling Arrangement For 169 screens For 43 screens Adjusting the projector’s elevator Elevator feetElevator button Connecting your devices Examples of connection with a VCR/DVD player Examples of connection with a computer Example of computer signal About Plug-and-Play capability Connecting power supply Loading batteries into the remote control Using the remote control Power on/off Turning on the power Turning off the power Adjusting the volume OperatingTemporarily muting the sound Selecting an input signal Searching an input signalPOWER INPUT  For no signal 43  For a 169 signalFor a 43 signal Selecting an aspect ratio Using the automatic adjustment feature Adjusting the zoom magnifying powerAdjusting the focus  For an RGB signal Adjusting the position Correcting the keystone distortions Using the partial magnify feature Freezing the screen Temporarily blanking the screen 1. To display a menu Multifunctional settingsUsing the menu function 2. To choose the target menu 3 Advanced MENU → EASY MENU 3. To choose the target item2 Advanced MENU → One of Advanced menus ex. SETUP menu 1 In the EASY MENU ex. KEYSTONE 5. To return to the previous menu 6. To reset4. To operate 7. To close the menu EASY MENU EASY MENU continued PICTURE menu To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOMUsing a test pattern PICTURE menu continued To adjust CUSTOMGAIN adjustments mainly affect color intensity on Using the buttons / switches the progress mode IMAGE menu IMAGE menu continued When this adjustment is too large, certain degradation may appearat the frame area of the picture. In such a case, please adjust small Choosing this item performs the automatic adjustment feature INPUT menu SETUP menu MIRROR item in the SETUP menu, if the projector screen is inclined SCREEN menu SCREEN menu continued Although the adjustable range will vary depending on inputs, andthe frame may not move for some signals. To restore the screen MyScreen Lock MESSAGE OPTION menu automatically. When the time is set to 1 to 99, and when the passedblinking. Please refer to the section “Turning off the power”.  OPTION menu continued continued press the ENTER button on the remote control or the INPUT buttonyou to clean “REMINDER...” will appear after the timer reaches the 50h  100h  200h  300h  TURN OFF Maintenance Lamp In the case of replacement by yourself Type number = DT00707 1 Press the MENU button to display a menu Usual ﬁlter cover Air ﬁlterType number = NJ22642 Filter cover for bottom-up use Filter cover for bottom-up use Caring for the cabinet and remote control Inside of the projectorCaring for the lens A note of precaution when cleaning the air ﬁlter TroubleshootingThere is no input signal Related messages The projector is in a standby state Regarding the indicator lampsThe projector is cooling down. A certain error The projector is in an on state Regarding the indicator lamps continued Phenomena that may easily be taken as machine defects If the situation cannot be corrected Perform picture adjustments by changing the COLOR TEMP, COLOR Warranty and after-service Speciﬁcations Speciﬁcations Dimension diagram202 285 33.5