Installer Setup, Setup Control | Home Automation 20A00-1 specification

INSTALLER SETUP

This section describes the items that the installer must setup as part of system installation. The Installer Setup mode is used to configure the general operation of the system, the Outputs, the Areas, the Zone Types, the Digital Communicator, and various other settings. This information is covered only in this manual. All other SETUP items, including delay times, names and voices, voice dialer, and codes are covered in the Owner's Manual, Document No. 20R00-1.

SETUP items are stored permanently in the system, even if the battery and AC power are disconnected. The "default" settings are the ones that have been set at the factory. You can review or change the setup items easily, as shown below.

Note: The default Installer Code is 1111.

To access the SETUP menu, press the 9 key and enter the installer code. To access the INSTALLER SETUP menu, press the # (INST) key.

INSTALLER SETUP MENU: 1=CTRL 2=ZONE 3=DCM ↓

4=AREA 5=TEMP 6=MISC

7=EXP↑

SETUP CONTROL

To configure X-10 and voltage outputs, from the Installer Setup menu, select the 1 (CTRL) key.

The base X-10 house code must be specified, as well as the output type for each of the 8 voltage outputs. The output type for both the interior and exterior horns may also be changed.

Press (") to advance to the next item, (!) to go back.

X-10 HOUSE CODE

The base house code is the house code for units 1-16 and is referenced as house code 1. The house code for the units 17-32 is the next house code after the base house code, or house code "B" if the base house code is "A". House codes "C" and "D" follows for Units 33-64.

X-10 HOUSE CODE: A

1-16=A-P↓

X-10 3-PHASE

This setting is used to select whether the X-10 signal is transmitted only at zero crossing for single phase (120V/240V) electrical systems or is transmitted at 0, 60, and 120 degrees for three phase electrical systems.

X-10	3-PHASE:	0
0=NO	1=YES	↕

To turn 3-Phase On, press 1 then ' # '. To turn 3-Phase Off, press 0 then ' # '. The burst at 60 and 120 degrees will be eliminated.

The default setting for 3-Phase is No.

Page 31

Image 37

Home Automation 20A00-1 installation manual Installer Setup, Setup Control, House Code

Contents

Installation Manual Page Home Automation, Inc Installation Manual Contents Installer Setup Figures Planning Introduction Controller Hookup Installation Controller Hookup About Security Zones Overall Connections Diagram About Fire Zones TWO-WIRE Fire Zone Connections FOUR-WIRE Fire Zone Connections Telephone Connections Refer to RJ31X Jack Connections for this configuration RJ31X Jack Connections LCD Console Hookup Console Setup Console Self Test Console Connections Sounder Outputs Sounder Connections Controller Outputs Reset OutputsOutput Applications Home Control Modules Remote ARM/DISARM Switch Remote Keyswitch Connections HAI Thermostats HAI Thermostat Connections Connections Programmable Energy Saver Modules TEMPERATURE, Outdoor TEMPERATURE, and Humidity Temperature / Humidity Sensor Connections Pesm Connections BUILT-IN Serial Port RS-232 Connections Console Check OUT System Power UP ProcedureTelephone Check OUT Fire Zone Check OUT Burglar Zone Check OUTHome Control Checkout Case of Trouble Customer Checkout Follow this procedure for removing the controller board Description of Contact ID Digital CommunicatorDescription of 4/2 Format Opening and Closing Reports Format Setup Control Installer SetupHouse Code Output Type Number Description Output Types Wireless Receiver Setup ZonesZone Resistors Type Through Z 48 Type Zone TypesZone Response Time Zone Type Number Description Description of Zone Types Latching Zone TypesENTRY/EXIT Duress Emergency Silent Dial OUT Police EmergencySupervised Fire Fire Emergency Outdoor Temperature Keyswitch InputTemperature Temperature Alarm First Phone NUMBER, First Account Number Setup Digital CommunicatorSecond Phone NUMBER, Second Account Number Communicator Type Automatic Test Time Report OPEN/CLOSE Setup Areas Control Setup Areas Setup Areas Buttons Setup Areas Zones Setup Areas Messages Setup Areas ConsolesSET-UP Areas Thermostats Temperature Display Setup TemperaturesThermostat Type Installer Code Setup MiscellaneousEnable PC Access PC Access Code Dial OUT Delay Outside Siren DelayAlarm Reset Time Fire Alarm Verification Supervise INT Sndr Enable Emergency KeysSupervise EXT Sndr Time Display Clock Adjustment AC Power FrequencyDate Display Dead Line Detect Reset System RAM Reset System EepromModel and Software Version Setup Expansion Function Types Number Description Serial 1 FunctionSerial 2 Rate VDC Omni II Specifications Underwriters Laboratories UL Installation Requirements Maximum current ratings for 24-hours Hour Standby Battery Capacity Smoke Detector Installation Guidelines Zone Type Trip Trouble Description Appendix a Contact ID Reporting Format Information for Central Station Appendix B Digital Communicator Code Sheet Code Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Code Zone Description Action to Take Page HAI New Orleans, LA U S a