Electrical Installation | Honeywell XYR 5000 LINE guide

3.2Electrical Installation

In this section wiring instructions are discussed for the various setup capabilities of the Base Radio. The subsections are as follows:

3.2.1 Electrical Specifications

3.2.2: Wiring Power to the Base Radio

3.2.3Wiring RS-485 to the Base Radio

3.2.4Wiring the RS-485/232 Converter to the Base Radio

3.2.5Wiring the RS-485/USB Converter to the Base Radio

3.2.6Daisy-Chaining Multiple Base Radios to Single RS-485/Power

3.2.7Terminating Communications Wiring to the Base Radio

3.2.8Grounding the Base Radio

3.2.9High Gain Antenna

Warning! Remember to turn off all power BEFORE attaching the Base Radio wires!

3.2.1Electrical Specifications

• 24VDC Power Supply with 0.5 Amp minimum output

Recommend 22AWG Power Supply wire

•2 Wire RS-485 Serial Communications Cable

Recommend Belden 3105A shielded and protected 22AWG or equivalent

•120 Ohm, ± 5%, ¼ W resistor for RS-485 termination

•RS-485 to RS-232 converter B&B model 485LDRC9 or equivalent

•8 AWG bare or green covered grounding cable for housing ground

In Figure 3-2,an overall wiring schematic is shown. Note that the grounding screw is located on the outside of the Base Radio housing.

7

Image 14

Honeywell XYR 5000 LINE manual Electrical Installation, Electrical Specifications

Contents

Base Radio User Guide XYR 5000 Line 34-XY-25-05 Rev 08/06Page Base Radio FCC Certification Telephone Revision NotesContacts Table of Contents Quare R OOT F Unction Overall Wiring Schematic Table of Figures About the Device Using this ManualIntroduction Unpacking Software Compatibility Overall Wiring Schematic Quick StartPage Base Radio Positioning InstallationMechanical Installation General Layout Electrical Installation Electrical Specifications Terminal Block Labels Wiring Power to the Base Radio Wiring RS-485 to the Base Radio Wiring the RS-485/232 Converter to the Base Radio Wiring RS-485 to the Base Radio Wiring the RS-485/USB Converter to the Base Radio USB Driver Installation USB Converter’s Male DB-9 Connector Daisy-Chaining Multiple Base Radios to Single RS-485/PowerWiring the DB-9 RS-485 Cable to the Base Radio USB Driver Un-installation Daisy-Chaining Power to Multiple Base Radios Daisy-Chaining RS-485 to Multiple Base Radios Terminating Communications Wiring to the Base Radio Daisy-Chaining RS-485 to Multiple Base Radios Grounding the Base Radio High Gain Antenna Read Only Sequence General ConfigurationBase Radio Displayed Messages Overall Configuration Menu Map Read Only Sequence Setting the User Password Menu Map to Password Setting Configuring the RF Communications RF Channel Selection Menu Map to RF Baud Rate Setting RF Baud Rate Selection High RF ID Setting High Rfid Setting Base Radio Setup Modbus Baud Rate Setting Modbus Device ID Setting Menu Map to Modbus Baud Rate SettingPage Modbus Parity Setting Modbus Mapping Mode Setting Modbus Communication Protocol Regmode Command 08- Diagnostic Modbus CommandsCommand 03-Read Holding Registers Command 17- Report Slave ID Command 11- Get Com Event CounterCommand 12- Get Com Event Log Register Address Description Register Type Command 43- Read Device IDBase Radio Holding Registers Register Address Description Base Radio On/Offline Transmitter Registers Base Radio Device Type RegistersBase Radio Device Status Registers Value Base Radio Device Status Transmitter Holding Registers Device ID Mapping ModeRegister Mapping Mode Register Address Transmitter Device Type Holding Registers Value Device Type Transmitter Device Status Registers Alarm Condition WN571 onlySquare Root Function Value Transmitter Device Status Technical Specifications Overall Base Radio Dimensions Appendix a Navigating the Menus Appendix B Base Radio Menu Map Figure A- 1 Base Radio Menu Map Appendix C Modbus Register Definitions Page Page Page Honeywell