Connecting User Inputs | HP E1366A, E1367A specs

Caution CENTER CONDUCTOR MAY SHORT TO SHIELD. Each channel’s center conductor may momentarily short to the shield when the channel is opened or closed. Use only resistive (50Ω or 75Ω) or current-limited (<1 A) inputs with less than 0.1 μF total capacitance.

Caution STATIC-SENSITIVE DEVICE. Use anti-static procedures when removing, configuring, and installing a module. The multiplexer modules are susceptible to static discharges. Do not install a multiplexer without its metal shield attached.

Connecting User Inputs

User inputs to the RF multiplexers are made through user-supplied male BNC connectors to the female BNC connectors on the modules. Figure 2-1 shows the multiplexer female BNC connectors and associated channel numbers.

Figure 2-1. BNC Connector Locations

18 Configuring the HP E1366A/E1367A RF Multiplexers

Chapter 2

Image 18

HP manual Connecting User Inputs, Configuring the HP E1366A/E1367A RF Multiplexers Chapter

Contents

Contents HP E1366A/E1367A RF Multiplexers Command Reference HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/67A RF Multiplexers User’s Manual Contents HP E1366A & E1367A RF Multiplexer Modules User’s Manual Documentation History December 5 According to ISO/IEC Guide 22 and EN HP E1366A & E1367A RF Multiplexer Modules User’s Manual Measurement Systems Division Reader Comment Sheet HP E1366A & E1367A RF Multiplexer Module User’s Manual Using This Chapter Getting Started with the HP E1366A/E1367A RF MultiplexersMultiplexer Module Description Multiplexers Switching Diagram Programming the Multiplexer Module Typical ConfigurationSpecifying Scpi Commands Address Multiplexer Card Numbers Multiplexer Channel Numbers Initial Operation Example RF Multiplexer Channel Lists/RangesPage Configuring the HP E1366A/E1367A RF Multiplexers Chapter Configuring the HP E1366A/E1367A RF Multiplexers Connecting User Inputs Configuring the HP E1366A/E1367A RF Multiplexers Chapter Hewlett-Packard BNC Cables Typical Multiplexer Configurations Standard Configuration Typical Tree Configuration Matrix-Type Configuration Typical Matrix-Type Configuration Changing Multiplexer Components RF Multiplexer Component Locations Configuring the HP E1366A/E1367A RF Multiplexers Chapter Switching Channels Using the HP E1366A/E1367A RF Multiplexer ModuleMultiplexer Commands Chapter Using the HP E1366A/E1367A RF Multiplexer Module Example Standard Switching Using the HP E1366A/E1367A RF Multiplexer Module Chapter Example Tree Switching Tree Switching Example Matrix-Type Switching Query Channel States. Use CLOSe? channellist or Example Scanning Using Trig Out Port Scanning Channels Scanning Channels Comments Understanding the HP E1366A/E1367A RF Multiplexers Scanning Channels CommandsUsing Scanning Trigger Sources Scanning with External Instruments Understanding the HP E1366A/E1367A RF Multiplexers Chapter Scanning Trigger Sources Example Scanning with External Device Scanning with External Device Example Scanning Using Trig Out Event Ports Using the Scan Complete Bit Example Scan Complete Interrupt Common Command Format HP E1366A/E1367A RF Multiplexers Command ReferenceCommand Types Scpi Command Format HP E1366A/E1367A RF Multiplexers Command Reference Chapter Semicolon between the commands. For example Subsystem Syntax ABORt Scpi Command ReferenceABORt Example Stopping a Scan with ABORt Subsystem Syntax ARM Parameters Example Query Number of Scanning Cycles Example Enabling the Monitor Mode DISPlaySubsystem Syntax DISPlay Example Select Module #2 in a Switchbox for Monitoring INITiate ∙ Non-Continuous Scanning Operation This is enabled with∙ Stopping Continuous Scans See the ABORt command Example Enabling Continuous Scans Example Query Continuous Scanning State OUTPut Example Enable Trig Out PortExample Query Trig Out Port Enable State Subsystem Syntax OUTPut Comments ∙ Closing Channels To close ROUTeSubsystem Syntax ROUTe Example Closing Multiplexer Channels Comments ∙ Opening Channels To openExample Opening Channels Open Example Scanning Using External Devices Example Query Scan Mode Example Selecting Paired-Channel Scanning Subsystem Syntax STATus ∙ Setting Bit 7 of the Status RegisterSTATus ∙ Returned Data after sending the STATusOPERationEVENt? SYSTem CTYPe?Subsystem Syntax SYSTem Comments ∙ RF Multiplexers Model Number ∙ RF Multiplexers Power-On State The power-on state is allExample Setting Card #1 Module to its Power-on State Example Reading the Model Number of a Card #1 Module Example Advancing Scan Using the TRIGger Command TRIGgerSubsystem Syntax TRIGger ∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Scanning Using External Triggers Example Scanning Using Bus TriggersExample Query Trigger Source Ieee 488.2 Common Commands Command Title Description Command Quick Reference Commands for the RF Multiplexer modules used in a switchbox Appendix a HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/E1367A RF Multiplexer SpecificationsInput Characteristics AC Performance General HP E1366A/E1367A RF Multiplexer Specifications Appendix a Typical Crosstalk channel-channel Cooling/Slot End of Life Detection Replacement Strategy Relay Life HP E1366A/E1367A RF Multiplexer Specifications Appendix a HP E1366A/E1367A Multiplexer Registers Appendix B HP E1366A/E1367A Multiplexer RegistersID Register Reading the Registers Status/Control Register Channel Enable RegistersAddressing the Registers ID/Device Type Registers Writing to the Registers HP E1366A/E1367A Multiplexer Registers Appendix B HP E1366A/E1367A RF Multiplexer Error Messages Appendix C HP E1366A/E1367A RF Multiplexer Error Messages HP E1366A/E1367A RF Multiplexer Error Messages Appendix C Index HP E1366A/67A RF Multiplexers User’s Manual Index HP-IB HP E1366A/67A RF Multiplexers User’s Manual Index HP E1366A/67A RF Multiplexers User’s Manual Index