Subsystem Syntax ARM, Parameters | HP E1367A, E1366A instruction

ARM

The ARM subsystem selects the number of scanning cycles (1 through 32767) for each INITiate command.

Subsystem Syntax ARM

:COUNt <number> MIN MAX

:COUNt? [MIN MAX]

:COUNt ARM:COUNt <number> MIN MAX allows scanning cycles to occur a multiple of times (1 to 32767) with one INITiate command when INITiate:CONTinuous OFF 0 is set. MIN sets 1 cycle and MAX sets 32767 cycles.

Parameters

Parameter Name	Parameter Type	Range of Values

<number>	numeric	1 32767 MIN MAX

Comments ∙ Number of Scans: Use only values between 1 to 32767 for the number of scanning cycles.

∙Related Commands: ABORt, INITiate:IMMediate

∙*RST Condition: ARM:COUNt 1

Example Setting Ten Scanning Cycles

This example sets an RF multiplexer for 10 scans of channels 00 through 03. When the scan sequence completes, channel 03 is closed.

ARM:COUN 10	! Set 10 scans per INIT command
SCAN (@100:103)	! Scan channels 00-03
INIT	! Start scan, close channel 00

Chapter 5

HP E1366A/E1367A RF Multiplexers Command Reference 41

Image 41

HP E1367A, E1366A manual Subsystem Syntax ARM, Parameters

Contents

Contents HP E1366A/E1367A RF Multiplexers Command Reference HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/67A RF Multiplexers User’s Manual Contents HP E1366A & E1367A RF Multiplexer Modules User’s Manual Documentation History According to ISO/IEC Guide 22 and EN December 5 HP E1366A & E1367A RF Multiplexer Modules User’s Manual Reader Comment Sheet Measurement Systems Division HP E1366A & E1367A RF Multiplexer Module User’s Manual Multiplexer Module Description Using This ChapterGetting Started with the HP E1366A/E1367A RF Multiplexers Multiplexers Switching Diagram Specifying Scpi Commands Typical ConfigurationProgramming the Multiplexer Module Address Multiplexer Channel Numbers Multiplexer Card Numbers Example RF Multiplexer Channel Lists/Ranges Initial OperationPage Chapter Configuring the HP E1366A/E1367A RF Multiplexers Configuring the HP E1366A/E1367A RF Multiplexers Configuring the HP E1366A/E1367A RF Multiplexers Chapter Connecting User Inputs Hewlett-Packard BNC Cables Standard Configuration Typical Multiplexer Configurations Typical Tree Configuration Typical Matrix-Type Configuration Matrix-Type Configuration RF Multiplexer Component Locations Changing Multiplexer Components Configuring the HP E1366A/E1367A RF Multiplexers Chapter Multiplexer Commands Using the HP E1366A/E1367A RF Multiplexer ModuleSwitching Channels Chapter Using the HP E1366A/E1367A RF Multiplexer Module Using the HP E1366A/E1367A RF Multiplexer Module Chapter Example Standard Switching Tree Switching Example Tree Switching Query Channel States. Use CLOSe? channellist or Example Matrix-Type Switching Scanning Channels Example Scanning Using Trig Out Port Scanning Channels Comments Using Scanning Trigger Sources Scanning Channels CommandsUnderstanding the HP E1366A/E1367A RF Multiplexers Scanning with External Instruments Understanding the HP E1366A/E1367A RF Multiplexers Chapter Scanning Trigger Sources Scanning with External Device Example Scanning with External Device Example Scanning Using Trig Out Event Ports Example Scan Complete Interrupt Using the Scan Complete Bit Command Types HP E1366A/E1367A RF Multiplexers Command ReferenceCommon Command Format Scpi Command Format HP E1366A/E1367A RF Multiplexers Command Reference Chapter Semicolon between the commands. For example ABORt Scpi Command ReferenceSubsystem Syntax ABORt Example Stopping a Scan with ABORt Parameters Subsystem Syntax ARM Example Query Number of Scanning Cycles Subsystem Syntax DISPlay Example Enabling the Monitor ModeDISPlay Example Select Module #2 in a Switchbox for Monitoring ∙ Stopping Continuous Scans See the ABORt command ∙ Non-Continuous Scanning Operation This is enabled withINITiate Example Enabling Continuous Scans Example Query Continuous Scanning State Example Query Trig Out Port Enable State Example Enable Trig Out PortOUTPut Subsystem Syntax OUTPut Subsystem Syntax ROUTe ROUTeComments ∙ Closing Channels To close Example Closing Multiplexer Channels Example Opening Channels Comments∙ Opening Channels To open Open Example Scanning Using External Devices Example Selecting Paired-Channel Scanning Example Query Scan Mode STATus ∙ Setting Bit 7 of the Status RegisterSubsystem Syntax STATus ∙ Returned Data after sending the STATusOPERationEVENt? Subsystem Syntax SYSTem SYSTemCTYPe? Example Setting Card #1 Module to its Power-on State ∙ RF Multiplexers Power-On State The power-on state is allComments ∙ RF Multiplexers Model Number Example Reading the Model Number of a Card #1 Module Subsystem Syntax TRIGger Example Advancing Scan Using the TRIGger CommandTRIGger ∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Query Trigger Source Example Scanning Using External TriggersExample Scanning Using Bus Triggers Command Title Description Ieee 488.2 Common Commands Commands for the RF Multiplexer modules used in a switchbox Command Quick Reference Input Characteristics AC Performance HP E1366A/E1367A RF Multiplexer SpecificationsAppendix a HP E1366A/E1367A RF Multiplexer Specifications General Typical Crosstalk channel-channel Cooling/Slot HP E1366A/E1367A RF Multiplexer Specifications Appendix a Relay Life End of Life Detection Replacement Strategy HP E1366A/E1367A RF Multiplexer Specifications Appendix a ID Register HP E1366A/E1367A Multiplexer RegistersAppendix B HP E1366A/E1367A Multiplexer Registers Addressing the Registers Status/Control Register Channel Enable RegistersReading the Registers ID/Device Type Registers Writing to the Registers HP E1366A/E1367A Multiplexer Registers Appendix B Appendix C HP E1366A/E1367A RF Multiplexer Error Messages HP E1366A/E1367A RF Multiplexer Error Messages HP E1366A/E1367A RF Multiplexer Error Messages Appendix C HP E1366A/67A RF Multiplexers User’s Manual Index Index HP-IB HP E1366A/67A RF Multiplexers User’s Manual Index HP E1366A/67A RF Multiplexers User’s Manual Index