Typical Multiplexer Configurations | HP E1366A, E1367A manual

Typical Multiplexer Configurations

Standard Configuration

Typical RF multiplexer configurations are:

∙Standard configuration (2 x 4:1 multiplexer)

∙Tree configuration (1 x 12:1 multiplexer)

∙Matrix-type configuration (4:1 to 4:1 multiplexer)

Figure 2-2 shows the standard configuration (2 x 4:1) for the RF multiplexers. With this configuration, you can switch channels 00-03 to com 00 and switch channels 10-13 to com 10. One channel per bank can be connected to its common at a time.

Figure 2-2. Typical Standard Configuration

20 Configuring the HP E1366A/E1367A RF Multiplexers

Chapter 2

Image 20

HP E1366A, E1367A manual Typical Multiplexer Configurations, Standard Configuration

Contents

Contents HP E1366A/E1367A RF Multiplexers Command Reference HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/67A RF Multiplexers User’s Manual Contents HP E1366A & E1367A RF Multiplexer Modules User’s Manual Documentation History December 5 According to ISO/IEC Guide 22 and EN HP E1366A & E1367A RF Multiplexer Modules User’s Manual Measurement Systems Division Reader Comment Sheet HP E1366A & E1367A RF Multiplexer Module User’s Manual Multiplexer Module Description Using This ChapterGetting Started with the HP E1366A/E1367A RF Multiplexers Multiplexers Switching Diagram Typical Configuration Specifying Scpi CommandsProgramming the Multiplexer Module Address Multiplexer Card Numbers Multiplexer Channel Numbers Initial Operation Example RF Multiplexer Channel Lists/RangesPage Configuring the HP E1366A/E1367A RF Multiplexers Chapter Configuring the HP E1366A/E1367A RF Multiplexers Connecting User Inputs Configuring the HP E1366A/E1367A RF Multiplexers Chapter Hewlett-Packard BNC Cables Typical Multiplexer Configurations Standard Configuration Typical Tree Configuration Matrix-Type Configuration Typical Matrix-Type Configuration Changing Multiplexer Components RF Multiplexer Component Locations Configuring the HP E1366A/E1367A RF Multiplexers Chapter Using the HP E1366A/E1367A RF Multiplexer Module Multiplexer CommandsSwitching Channels Chapter Using the HP E1366A/E1367A RF Multiplexer Module Example Standard Switching Using the HP E1366A/E1367A RF Multiplexer Module Chapter Example Tree Switching Tree Switching Example Matrix-Type Switching Query Channel States. Use CLOSe? channellist or Example Scanning Using Trig Out Port Scanning Channels Scanning Channels Comments Scanning Channels Commands Using Scanning Trigger SourcesUnderstanding the HP E1366A/E1367A RF Multiplexers Scanning with External Instruments Understanding the HP E1366A/E1367A RF Multiplexers Chapter Scanning Trigger Sources Example Scanning with External Device Scanning with External Device Example Scanning Using Trig Out Event Ports Using the Scan Complete Bit Example Scan Complete Interrupt HP E1366A/E1367A RF Multiplexers Command Reference Command TypesCommon Command Format Scpi Command Format HP E1366A/E1367A RF Multiplexers Command Reference Chapter Semicolon between the commands. For example Scpi Command Reference ABORtSubsystem Syntax ABORt Example Stopping a Scan with ABORt Subsystem Syntax ARM Parameters Example Query Number of Scanning Cycles Subsystem Syntax DISPlay Example Enabling the Monitor ModeDISPlay Example Select Module #2 in a Switchbox for Monitoring ∙ Non-Continuous Scanning Operation This is enabled with ∙ Stopping Continuous Scans See the ABORt commandINITiate Example Enabling Continuous Scans Example Query Continuous Scanning State Example Enable Trig Out Port Example Query Trig Out Port Enable StateOUTPut Subsystem Syntax OUTPut ROUTe Subsystem Syntax ROUTeComments ∙ Closing Channels To close Example Closing Multiplexer Channels Example Opening Channels Comments∙ Opening Channels To open Open Example Scanning Using External Devices Example Query Scan Mode Example Selecting Paired-Channel Scanning ∙ Setting Bit 7 of the Status Register STATusSubsystem Syntax STATus ∙ Returned Data after sending the STATusOPERationEVENt? Subsystem Syntax SYSTem SYSTemCTYPe? ∙ RF Multiplexers Power-On State The power-on state is all Example Setting Card #1 Module to its Power-on StateComments ∙ RF Multiplexers Model Number Example Reading the Model Number of a Card #1 Module Subsystem Syntax TRIGger Example Advancing Scan Using the TRIGger CommandTRIGger ∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Query Trigger Source Example Scanning Using External TriggersExample Scanning Using Bus Triggers Ieee 488.2 Common Commands Command Title Description Command Quick Reference Commands for the RF Multiplexer modules used in a switchbox HP E1366A/E1367A RF Multiplexer Specifications Input Characteristics AC PerformanceAppendix a HP E1366A/E1367A RF Multiplexer Specifications General HP E1366A/E1367A RF Multiplexer Specifications Appendix a Typical Crosstalk channel-channel Cooling/Slot End of Life Detection Replacement Strategy Relay Life HP E1366A/E1367A RF Multiplexer Specifications Appendix a ID Register HP E1366A/E1367A Multiplexer RegistersAppendix B HP E1366A/E1367A Multiplexer Registers Status/Control Register Channel Enable Registers Addressing the RegistersReading the Registers ID/Device Type Registers Writing to the Registers HP E1366A/E1367A Multiplexer Registers Appendix B HP E1366A/E1367A RF Multiplexer Error Messages Appendix C HP E1366A/E1367A RF Multiplexer Error Messages HP E1366A/E1367A RF Multiplexer Error Messages Appendix C Index HP E1366A/67A RF Multiplexers User’s Manual Index HP-IB HP E1366A/67A RF Multiplexers User’s Manual Index HP E1366A/67A RF Multiplexers User’s Manual Index