Subsystem Syntax OUTPut | HP E1367A, E1366A specification

OUTPut

The OUTPut subsystem enables or disables the “ Trig Out” port of the

HP E1300A/E1301A mainframe or the HP E1405A/E1406A module.

Subsystem Syntax OUTPut

[:STATe] ON OFF 1 0 [:STATe]?

[:STATe] OUTPut[:STATe] ON OFF 1 0 enables/disables the “ Trig Out” port on the rear panel of the HP E1300A/E1301A mainframe or the

HP E1405A/E1406A module. OUTPut[:STATe] ON 1 enables the port and OUTPut[:STATe] OFF 0 disables the port.

Parameters

Parameter Name	Parameter Type	Range of Values

ON OFF 1 0	boolean	ON OFF 1 0

Comments ∙ Enabling “Trig Out” Port: When enabled, a pulse is output from the “ Trig Out” port after each scanned switchbox channel is closed. If disabled, a pulse is not output from the port after channel closures. The output pulse is a +5 V negative-going pulse.

∙“Trig Out” Port Shared by Switchboxes: When enabled, the “ Trig Out” port is pulsed by any switchbox each time a scanned channel is closed. To disable the output for a specific switchbox, send the OUTPut[:STATe] OFF or OUTPut[:STATe] 0 command for that switchbox.

∙Related Commands: [ROUTE:]SCAN, TRIGger:SOURce

∙*RST Condition: OUTPut[:STATe] OFF (port disabled)

Example Enable "Trig Out" Port

OUTP:STAT ON	! Enable “Trig Out” port to output
	pulse after each scanned channel is
	closed

[:STATe]? OUTPut[:STATe]? queries the present state of the “ Trig Out” port. The command returns 1 if the port is enabled or 0 if the port is disabled.

Example Query “Trig Out” Port Enable State

This example enables the “ Trig Out” Port and queries the enable state. The

OUTPut[:STATe]? command returns 1 since the port is enabled.

OUTP:STAT ON	! Enable “Trig Out” port
OUTP:STAT?	! Query port enable state

Chapter 5

HP E1366A/E1367A RF Multiplexers Command Reference 47

Image 47

HP E1367A, E1366A manual Subsystem Syntax OUTPut, Example Enable Trig Out Port, Example Query Trig Out Port Enable State

Contents

Contents HP E1366A/E1367A RF Multiplexers Command Reference HP E1366A/E1367A RF Multiplexer Specifications HP E1366A/67A RF Multiplexers User’s Manual Contents HP E1366A & E1367A RF Multiplexer Modules User’s Manual Documentation History According to ISO/IEC Guide 22 and EN December 5 HP E1366A & E1367A RF Multiplexer Modules User’s Manual Reader Comment Sheet Measurement Systems Division HP E1366A & E1367A RF Multiplexer Module User’s Manual Multiplexer Module Description Using This ChapterGetting Started with the HP E1366A/E1367A RF Multiplexers Multiplexers Switching Diagram Address Typical ConfigurationSpecifying Scpi Commands Programming the Multiplexer Module Multiplexer Channel Numbers Multiplexer Card Numbers Example RF Multiplexer Channel Lists/Ranges Initial OperationPage Chapter Configuring the HP E1366A/E1367A RF Multiplexers Configuring the HP E1366A/E1367A RF Multiplexers Configuring the HP E1366A/E1367A RF Multiplexers Chapter Connecting User Inputs Hewlett-Packard BNC Cables Standard Configuration Typical Multiplexer Configurations Typical Tree Configuration Typical Matrix-Type Configuration Matrix-Type Configuration RF Multiplexer Component Locations Changing Multiplexer Components Configuring the HP E1366A/E1367A RF Multiplexers Chapter Chapter Using the HP E1366A/E1367A RF Multiplexer Module Using the HP E1366A/E1367A RF Multiplexer ModuleMultiplexer Commands Switching Channels Using the HP E1366A/E1367A RF Multiplexer Module Chapter Example Standard Switching Tree Switching Example Tree Switching Query Channel States. Use CLOSe? channellist or Example Matrix-Type Switching Scanning Channels Example Scanning Using Trig Out Port Scanning Channels Comments Scanning with External Instruments Scanning Channels CommandsUsing Scanning Trigger Sources Understanding the HP E1366A/E1367A RF Multiplexers Understanding the HP E1366A/E1367A RF Multiplexers Chapter Scanning Trigger Sources Scanning with External Device Example Scanning with External Device Example Scanning Using Trig Out Event Ports Example Scan Complete Interrupt Using the Scan Complete Bit Scpi Command Format HP E1366A/E1367A RF Multiplexers Command ReferenceCommand Types Common Command Format HP E1366A/E1367A RF Multiplexers Command Reference Chapter Semicolon between the commands. For example Example Stopping a Scan with ABORt Scpi Command ReferenceABORt Subsystem Syntax ABORt Parameters Subsystem Syntax ARM Example Query Number of Scanning Cycles Subsystem Syntax DISPlay Example Enabling the Monitor ModeDISPlay Example Select Module #2 in a Switchbox for Monitoring Example Enabling Continuous Scans ∙ Non-Continuous Scanning Operation This is enabled with∙ Stopping Continuous Scans See the ABORt command INITiate Example Query Continuous Scanning State Subsystem Syntax OUTPut Example Enable Trig Out PortExample Query Trig Out Port Enable State OUTPut Example Closing Multiplexer Channels ROUTeSubsystem Syntax ROUTe Comments ∙ Closing Channels To close Example Opening Channels Comments∙ Opening Channels To open Open Example Scanning Using External Devices Example Selecting Paired-Channel Scanning Example Query Scan Mode ∙ Returned Data after sending the STATusOPERationEVENt? ∙ Setting Bit 7 of the Status RegisterSTATus Subsystem Syntax STATus Subsystem Syntax SYSTem SYSTemCTYPe? Example Reading the Model Number of a Card #1 Module ∙ RF Multiplexers Power-On State The power-on state is allExample Setting Card #1 Module to its Power-on State Comments ∙ RF Multiplexers Model Number Subsystem Syntax TRIGger Example Advancing Scan Using the TRIGger CommandTRIGger ∙ Trig Out Port Shared by Switchboxes See the OUTPut command Example Query Trigger Source Example Scanning Using External TriggersExample Scanning Using Bus Triggers Command Title Description Ieee 488.2 Common Commands Commands for the RF Multiplexer modules used in a switchbox Command Quick Reference General HP E1366A/E1367A RF Multiplexer SpecificationsInput Characteristics AC Performance Appendix a HP E1366A/E1367A RF Multiplexer Specifications Typical Crosstalk channel-channel Cooling/Slot HP E1366A/E1367A RF Multiplexer Specifications Appendix a Relay Life End of Life Detection Replacement Strategy HP E1366A/E1367A RF Multiplexer Specifications Appendix a ID Register HP E1366A/E1367A Multiplexer RegistersAppendix B HP E1366A/E1367A Multiplexer Registers ID/Device Type Registers Status/Control Register Channel Enable RegistersAddressing the Registers Reading the Registers Writing to the Registers HP E1366A/E1367A Multiplexer Registers Appendix B Appendix C HP E1366A/E1367A RF Multiplexer Error Messages HP E1366A/E1367A RF Multiplexer Error Messages HP E1366A/E1367A RF Multiplexer Error Messages Appendix C HP E1366A/67A RF Multiplexers User’s Manual Index Index HP-IB HP E1366A/67A RF Multiplexers User’s Manual Index HP E1366A/67A RF Multiplexers User’s Manual Index