HP XU700 Basic Pre-bootDiagnostics

6 Tests and Error Messages

MaxiLife Test Sequence and Error Messages

Basic Pre-boot Diagnostics

The first diagnostic (called basic pre-boot diagnostics) is run to check the presence of the processor(s) or terminators, power supply, hardware monitoring and thermal sensors. Simply by having a power cord connected to the PC Workstation activates the Basic Pre-boot Diagnostics.

The pre-boot diagnostic tests are run in order of priority with respect to their importance to computer functions.

On the HP Kayak XU700 PC Workstation, the first detected error displays a message on the LCD status panel. If this happens, one of the following screens could appear.

Presence of processor, or			Control of some voltages:
processor terminator			12V, 3.3V, 1.8V, 2.5V, -5V

	ERROR			ERROR

CPU Socket

Power Supply

Missing or incorrectly installed	If a Power Supply error is displayed, a cause could be
processor or processor terminator	with the power supply cabling or circuits.

The following diagram shows how the Pre-boot Diagnostics works when it encounters an error.

Vcc State (5V)

CPU or Terminator

Voltage 12V, 3.3V, 1.8V, 2.5V

Voltage CPU1, CPU2

I2C Bus

MaxiLife Firmware

Hardware

Temperature

System

Monitoring

Sensors

Memory

LCD Status Panel

An error has been detected when checking the

ERROR

processor and processor terminator. The

CPU Socket

displayed error message could indicate a missing

processor or processor terminator.

98

Contents

Page Notice The information contained in this document is subject to change without notice Adaptec® is a registered trademark of Adaptec, Inc Hewlett-PackardFrance Business Desktop Division (BDD) Contents 1 System Overview 2 System Board 3 Interface Cards 4 Mass Storage Devices 5 HP BIOS 6 Tests and Error Messages 7 Connectors and Sockets Page Preface Conventions Hexadecimal numbers are identified by a lower case h For example, 0FFFFFFFh or 32F5h Bibliography Extra Information Can Be ❒ nVIDIA graphics cards Obtained At: System Overview 1 System Overview HP Kayak XU700 PC Workstation Overview HP MaxiLife Utility and a LCD status panel Operating System Page Page Front and Side Views Rear View HP Kayak XU700 Minitower Front Panel The front panel of has the following features: Liquid Crystal Display •On/Off LED. There are five states: Physical Characteristics Electrical Specifications Power Consumption and Cooling Environmental Specifications Power Saving and Ergonometry Power Saving and Ergonometry for APM Systems Power Saving Modes and Resume Events for ACPI Systems Power-Onfrom Space-Bar Soft Power Down Documentation Access HP World Wide Web Site After accessing the site, select HP Kayak XU700 PC Workstation Where to Find the Information Opening the PC Full description Supported accessories Installing Page Page System Board System Board Overview Architectural View AGP Slot PCI Slots PCI Slot The PCI slots are connected to the ICH2 PCI 32-bit33 MHz bus System Board Switches Switch Use Reserved. Do Not change Default Settings Reserved. Do Not change Default Setting Chipset Hub Link 8-bit.The MCH chip feature is described in detail on page IDE controller (Ultra ATA/100) (Alert-On-LAN) and Real Time Clock (RTC) and CMOS Memory Controller Hub (82850) The following table shows the features that are available in the MCH Host Bridge/Controller MCH Interface Accelerated Graphics Port (AGP) Bus Interface AGP 4x Bus Main Memory Controller Dual Rambus Bus RIMM Memory Slots The HP Kayak XU700 PC Workstation has four RIMM memory sockets memory modules Each pair of memory sockets must contain identical memory modules identical modules, and sockets A2 and B2 must contain identical modules The Input/Output Controller Hub 2 (82801BA) The following table shows the available ICH2 features ICH2 Architecture ICH2 PCI Bus Interface Refer to the table page 59for ICH2 interrupts SMBus Controller Low Pin Count Interface AC’97 Controller This is the single-chipCS4299 audio controller that provides full audio features for the Kayak XU700 Refer to page 46for information about the CS4299 audio solution IDE Controller Crystal CS4299 Integrated PCI Audio Devices on the SMBus Page ICH2 SMBus Master the SMBus is done through the ICH2 SMBus interface. Typically, the processor has access to all the devices connected to the SMBus DIMM Sockets used to store data online Page MaxiLife Architecture power cord is plugged in Devices on the Low Pin Count Bus The Super I/O Controller (NS 87364) FirmWare Hub (82802AB) The following table shows the available FWH features Page System Bus Intel Pentium 4 Processor Cache Memory Input/Output Controller Hub Interrupts PCI 64-bitHub Interrupts Interrupt Controllers Interrupt Source There are three major interrupt modes available: PIC mode: PCI Interrupt Request Lines Page Interface Cards Matrox Millennium G450 Graphics Card 3D Features Available Video Resolutions The following table summarizes the maximum supported resolutions Limitations NVIDIA Quadro2 MXR HP 10/100 TX PCI LAN Interface HP 10/100 TX PCI LAN Interface Features Feature: Description: HP 10/100 TX PCI LAN Interface LED Descriptions LED Supported LAN Cards 3COM NIC (Network Interconnect) LAN Card 3COM LAN Card LED Descriptions GREEN: Adaptec 29160 SCSI PCI Adapter Card CAUTION: SCSI devices to connectors 1 and SCSI Cable Information Cable Number Cable Length Additional SCSI Card Features Feature Mass Storage Devices Flexible Disk Drives Hard Disk Drives SCSI Hard Disk Drives Quantum Atlas 10K CD-ROMDrives 8X Video IDE DVD-ROMDrive DVD-ROM drive 4X IDE CD-WriterPlus Drive CD-RW Page HP BIOS Using the HP Setup Program Advanced Screen Processors, Memory and Cache 1.Only if ECC modules are detected Floppy Disk Drives IDE Devices IDE Primary Master Device Integrated USB Interface Integrated I/O Ports Integrated Audio Device AGP Configuration (Video) PCI Device, Slot #1 Security Screen Hardware Protection Boot Screen •Hard disk drives •Removable devices Boot Device Priority Power Screen Updating the System BIOS Restoring BIOS Default Settings 2Press to load the default settings from the Setup program 3Set the “Reset Configuration Data” to Yes in the Main menu If You Forgot the Administrator Password Esc Exit Menu Clearing the CMOS Recovering the BIOS (Crisis Mode) Recovering the BIOS (Crisis Mode) 1Obtain a bootable DOS floppy disk 2Copy the BIOS files on to the floppy disk How to download the system BIOS is described on page (rename the BIOS filename with the one on the floppy disk) System Memory Map HP I/O Port Map (I/O Addresses Used by the System1) DMA Channel Controllers I/O APIC IRQ Interrupt Request Description Input Page Page Tests and Error Messages Basic Pre-bootDiagnostics Pre-bootDiagnostics Error Codes Post Test Sequence and Post Error Operating System Boot Phase Run-TimeErrors Main Menu (Minitower models only) System Info Boot Steps Boot report Refer to the online Troubleshooting Guide Order in Which POST Tests Are Performed but the suggestions for corrective action (refer to for a brief summary) , the LCD status panel displays either a message, a POST code number (refer to ) or an EMU code The following table lists the POST checkpoint codes and their associated Page Page Page Page Page Page Initialize video Initialize System Management Mode Output one beep before boot Boot to Mini DOS Clear Huge Segment Error Message Summary Category #1: WARNING1 00100 Keyboard Error Category #2: Cause / Symptom 0000h Any POST error that is not listed below System error 0010h Page Other Connectors and Sockets Additional SCSI LED Additional SCSI LED Connector (4-pin) Aux Power Connector Power Supply Connector for Internal Audio CD AUDIO Connector I/O Internal Speaker AUX Connector Hard Disk Drive Temperature Connector HDD Temperature VGA DB15 Connector VGA DB Connector Pins Ethernet UTP Connector Rear Panel Socket Pin Layouts Keyboard and Mouse Keyboard and Mouse Connectors Data Not Used USB Connector 9-pinSerial Port Connector 25-pinParallel Connector 25-pinParallel Connector MIDI/Joystick MIDI/Joystick Connector External Audio Jacks