Safety Instructions, I. General operation | Husqvarna Pro 15

Image 3

Husqvarna Pro 15 Safety Instructions, Safe operation practices for ride-on mowers, I. General operation, III. Children

Contents

101 Rider ProOperator´s manual IMPORTANT INFORMATION CONTENTS Operator’s Manual for Rider Pro II. Slope operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers I. General operation Intended use IV. ServiceTravel and transport on public roads Towing Towing INSTRUCTIONDear customer Driving and transport on public roads Serial number Good service EXPLANATION OF SYMBOLS Never carry passengers General useRead the instructions before starting the machine Clear the area from stones etc. before cutting Cut slopes upwards and downwards, not sideways Be extra careful when driving on slopesDriving on slopes Do as follows Never allow children to drive the machine MaintenanceChildren Keep children away from the mowing area Do not alter the setting of the governor and do not race the engine Never smoke in the vicinity of the battery or the fuelClean the machine regularly from grass, leaves and other waste Never drive the machine in an enclosed space PRESENTATION PresentationLocation of the controls Throttle control Choke leverSpeed limiter Cutting unit Lift lever for cutting unitLifting of the cutting unit Lowering of the cutting unit Fuelling Lever for adjustment of the cutting heightParking brake Seat DRIVING Before startingStarting the engine Driving the machine Mowing pattern Cutting tips Release lever Stopping the engine Maintenance interval in MAINTENANCEMaintenance schedule Maintenance The cutting unit is disengaged The engine is switched offThe parking brake is applied The ignition key is removed Right-hand fender Removing of the machine hoodsEngine hood Front hood Transmission cover Checking and adjustment of the steering wires Poorly adjusted brakes can result in reduced braking power Adjusting the brakesChecking and adjustment of the throttle wire Checking and adjusting the choke wire Checking of the fuel pump’s air filter Replacement of the fuel filter Do not use compressed air to clean the paper filter Replacing the air filterDo not wash the paper filter Do not oil the paper filter Muffler air intake Cleaning the filterCheck the transmission’s air intake Check the engine’s cooling air intake Procedures on contact with acid Check the level of the battery acid Inspecting the safety system Checking the tyre pressure The tyre pressure should be 60 kPa 0.6 kp/cm2 all roundThe maximum tyre pressure is 80 kPa 0,8 kp/cm2 Fitting the cutting unit Installing BioClip Checking and adjustment of the cutting unit’s ground pressureBioClip Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unit Removing the belt Removing the cutting unit BioClip 103 Versions 1 and BioClip 103 Versions 1 and Belt replacement on the BioClipProtect your hands by wearing gloves when working with the blades Replacing the cutting unit’s belts Belt replacement on cutting unit’s with side or rear ejectors Belt replacement on BioClip Placing in service position Service position for cutting unit 5. Disengage the spring from the drive belt tensioning wheel Restoring from service position Checking the blades Cutting units with rear ejection Cutting units with side ejectionBioClip103 BioClip Replacing the break-pin BioClip 1/52 1/365 Lubrication chartLUBRICATION 12/12 1/12 Lubricating wires General1. Cutting unit 2. Pedal mechanism in frame tunnel 3. Chains in frame tunnel4. Triangular link and joints 6. Throttle and choke wires, lever bearings 5. Driver’s seat7. Belt tensioner 8. Engine oil Changing the engine oilFULL 10. Parking brake wire 9. Gear lever11. Transmission oil level Avoid skin contact, wash with soap and water in the event of spillage 12. Transmission13. Replacing the oil filter IMPORTANT INFORMATION Dispose of used filters at a recycling station TROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage Explanation of colour abbreviations in wiring diagram WIRING DIAGRAM1. Microswitch, hydrostatic transmission 2. Microswitch, cutting unit 3. Microswitch, seat 4. Ignition lock 5. Counter 6. Start relay Electrical system TECHNICAL DATARider Pro Engine Rear ejector EU declaration of conformity Only applies to EuropeBioClip Side ejector SERVICEJOURNAL Pre-delivery serviceWork done 54 - English 25 hour service 50 hour service 56 - English 100/200 hour service 300 hour service 58 - English At least once a season Date, mileage, stamp, sign 60 - English ´*3-Q¶5w¨Page 2001W02