Replacing the break-pin BioClip, Maintenance | Husqvarna Pro 15

Image 41

Husqvarna Pro 15 manual Replacing the break-pin BioClip, Maintenance

Contents

Operator´s manual 101Rider Pro IMPORTANT INFORMATION CONTENTS Operator’s Manual for Rider Pro Safe operation practices for ride-on mowers SAFETY INSTRUCTIONSI. General operation II. Slope operation Travel and transport on public roads IV. ServiceTowing Intended use Dear customer INSTRUCTIONDriving and transport on public roads Towing Serial number Good service EXPLANATION OF SYMBOLS Read the instructions before starting the machine General useClear the area from stones etc. before cutting Never carry passengers Driving on slopes Be extra careful when driving on slopesDo as follows Cut slopes upwards and downwards, not sideways Children MaintenanceKeep children away from the mowing area Never allow children to drive the machine Clean the machine regularly from grass, leaves and other waste Never smoke in the vicinity of the battery or the fuelNever drive the machine in an enclosed space Do not alter the setting of the governor and do not race the engine Location of the controls PRESENTATIONPresentation Speed limiter Throttle controlChoke lever Lifting of the cutting unit Lowering of the cutting unit Cutting unitLift lever for cutting unit Parking brake Lever for adjustment of the cutting heightSeat Fuelling Starting the engine DRIVINGBefore starting Driving the machine Mowing pattern Cutting tips Release lever Stopping the engine Maintenance schedule MAINTENANCEMaintenance Maintenance interval in The parking brake is applied The engine is switched offThe ignition key is removed The cutting unit is disengaged Engine hood Removing of the machine hoodsFront hood Right-hand fender Transmission cover Checking and adjustment of the steering wires Checking and adjustment of the throttle wire Adjusting the brakesChecking and adjusting the choke wire Poorly adjusted brakes can result in reduced braking power Checking of the fuel pump’s air filter Replacement of the fuel filter Do not wash the paper filter Do not oil the paper filter Do not use compressed air to clean the paper filterReplacing the air filter Check the transmission’s air intake Cleaning the filterCheck the engine’s cooling air intake Muffler air intake Procedures on contact with acid Check the level of the battery acid Inspecting the safety system The maximum tyre pressure is 80 kPa 0,8 kp/cm2 Checking the tyre pressureThe tyre pressure should be 60 kPa 0.6 kp/cm2 all round Fitting the cutting unit BioClip Installing BioClipChecking and adjustment of the cutting unit’s ground pressure Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unit Removing the belt Removing the cutting unit Protect your hands by wearing gloves when working with the blades Belt replacement on the BioClipReplacing the cutting unit’s belts BioClip 103 Versions 1 and BioClip 103 Versions 1 and Belt replacement on cutting unit’s with side or rear ejectors Belt replacement on BioClip Placing in service position Service position for cutting unit 5. Disengage the spring from the drive belt tensioning wheel Restoring from service position BioClip103 BioClip Checking the bladesCutting units with rear ejection Cutting units with side ejection Replacing the break-pin BioClip LUBRICATION Lubrication chart12/12 1/12 1/52 1/365 1. Cutting unit Lubricating wiresGeneral 4. Triangular link and joints 2. Pedal mechanism in frame tunnel3. Chains in frame tunnel 7. Belt tensioner 6. Throttle and choke wires, lever bearings5. Driver’s seat FULL 8. Engine oilChanging the engine oil 11. Transmission oil level 10. Parking brake wire9. Gear lever 13. Replacing the oil filter 12. TransmissionIMPORTANT INFORMATION Dispose of used filters at a recycling station Avoid skin contact, wash with soap and water in the event of spillage Procedure TROUBLE SHOOTING SCHEDULEProblem Winter storage ServiceSTORAGE 1. Microswitch, hydrostatic transmission 2. Microswitch, cutting unit WIRING DIAGRAM3. Microswitch, seat 4. Ignition lock 5. Counter 6. Start relay Explanation of colour abbreviations in wiring diagram Rider Pro TECHNICAL DATAEngine Electrical system BioClip EU declaration of conformity Only applies to EuropeSide ejector Rear ejector Work done SERVICEJOURNALPre-delivery service 54 - English 25 hour service 50 hour service 56 - English 100/200 hour service 300 hour service 58 - English At least once a season Date, mileage, stamp, sign 60 - English ´*3-Q¶5w¨Page 2001W02