Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna Pro 15 hour service, Servicejournal, Work done, Date, mileage, stamp, sign, English

Models: Pro 15

1 63

Download 63 pages 11.32 Kb

Page 55

Image 55

SERVICEJOURNAL

Work done

Date, mileage, stamp, sign

25 hour service

1.Clean the air filter pre-filter (oil-foam element). (more regularly in dusty conditions)

2.Clean the engine cooling air intake and transmission air intake.

3.Clean the fuel pump air filter. (in dusty conditions).

54 – English

Page 55

Image 55

Husqvarna Pro 15 manual hour service, Servicejournal, Work done, Date, mileage, stamp, sign, English

Contents

Rider Pro 101 91Operator´s manual IMPORTANT INFORMATION CONTENTS Operator’s Manual for Rider ProII. Slope operation SAFETY INSTRUCTIONSSafe operation practices for ride-on mowers I. General operationIntended use IV. ServiceTravel and transport on public roads TowingTowing INSTRUCTIONDear customer Driving and transport on public roadsSerial number Good serviceSAFETY INSTRUCTIONS EXPLANATION OF SYMBOLS Never carry passengers General useRead the instructions before starting the machine Clear the area from stones etc. before cuttingCut slopes upwards and downwards, not sideways Be extra careful when driving on slopesDriving on slopes Do as followsNever allow children to drive the machine MaintenanceChildren Keep children away from the mowing areaSAFETY INSTRUCTIONS Never smoke in the vicinity of the battery or the fuelClean the machine regularly from grass, leaves and other waste Never drive the machine in an enclosed spacePresentation PRESENTATIONLocation of the controls PRESENTATION Throttle controlChoke lever Speed limiterPRESENTATION Cutting unitLift lever for cutting unit Lifting of the cutting unit Lowering of the cutting unitFuelling Lever for adjustment of the cutting heightParking brake SeatBefore starting DRIVINGStarting the engine DRIVING Driving the machineIMPORTANT INFORMATION Mowing pattern Cutting tipsDRIVING Release lever Stopping the engineDRIVING Maintenance interval in MAINTENANCEMaintenance schedule MaintenanceThe cutting unit is disengaged The engine is switched offThe parking brake is applied The ignition key is removedRight-hand fender Removing of the machine hoodsEngine hood Front hoodTransmission cover Checking and adjustment of the steering wiresMAINTENANCE Poorly adjusted brakes can result in reduced braking power Adjusting the brakesChecking and adjustment of the throttle wire Checking and adjusting the choke wireChecking of the fuel pump’s air filter Replacement of the fuel filterMAINTENANCE MAINTENANCE Do not use compressed air to clean the paper filterReplacing the air filter Do not wash the paper filter Do not oil the paper filterMuffler air intake Cleaning the filterCheck the transmission’s air intake Check the engine’s cooling air intakeEnglish Check the level of the battery acidProcedures on contact with acid MAINTENANCEMAINTENANCE Inspecting the safety systemThe maximum tyre pressure is 80 kPa 0,8 kp/cm2 Checking the tyre pressureMAINTENANCE The tyre pressure should be 60 kPa 0.6 kp/cm2 all roundMAINTENANCE Fitting the cutting unitMAINTENANCE Installing BioClipChecking and adjustment of the cutting unit’s ground pressure BioClipChecking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitMAINTENANCE Removing the belt Removing the cutting unitMAINTENANCE BioClip 103 Versions 1 and BioClip 103 Versions 1 and Belt replacement on the BioClipProtect your hands by wearing gloves when working with the blades Replacing the cutting unit’s beltsIMPORTANT INFORMATION Belt replacement on BioClipBelt replacement on cutting unit’s with side or rear ejectors MAINTENANCEPlacing in service position Service position for cutting unitMAINTENANCE 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCEMAINTENANCE Restoring from service positionMAINTENANCE Checking the bladesCutting units with rear ejection Cutting units with side ejection BioClip103 BioClipMAINTENANCE Replacing the break-pin BioClip1/52 1/365 Lubrication chartLUBRICATION 12/12 1/12LUBRICATION Lubricating wiresGeneral 1. Cutting unitLUBRICATION 2. Pedal mechanism in frame tunnel3. Chains in frame tunnel 4. Triangular link and jointsLUBRICATION 6. Throttle and choke wires, lever bearings5. Driver’s seat 7. Belt tensionerIMPORTANT INFORMATION 8. Engine oilChanging the engine oil LUBRICATIONLUBRICATION 10. Parking brake wire9. Gear lever 11. Transmission oil levelAvoid skin contact, wash with soap and water in the event of spillage 12. Transmission13. Replacing the oil filter IMPORTANT INFORMATION Dispose of used filters at a recycling stationProblem TROUBLE SHOOTING SCHEDULEProcedure STORAGE ServiceWinter storage Explanation of colour abbreviations in wiring diagram WIRING DIAGRAM1. Microswitch, hydrostatic transmission 2. Microswitch, cutting unit 3. Microswitch, seat 4. Ignition lock 5. Counter 6. Start relayElectrical system TECHNICAL DATARider Pro EngineRear ejector EU declaration of conformity Only applies to EuropeBioClip Side ejectorPre-delivery service SERVICEJOURNALWork done Date, mileage, stamp, sign 25 hour serviceSERVICEJOURNAL Work doneSERVICEJOURNAL 50 hour serviceWork done 56 - English 100/200 hour serviceSERVICEJOURNAL Work doneSERVICEJOURNAL 300 hour serviceWork done 58 - English At least once a seasonSERVICEJOURNAL Work doneEnglish Date, mileage, stamp, signSERVICEJOURNAL Work doneDate, mileage, stamp, sign ´*3-Q¶5w¨SERVICEJOURNAL Work donePage ´*3-Q¶5w¨ 2001W02