Manuals / hussman / Kitchen Appliance / Refrigerator

hussman P/N 0420057_B P/N 0420057B, Joining Instructions, Installing Coil Cover And Drip Tray

Models: P/N 0420057_B

1 46

Download 46 pages 55.32 Kb

Page 14

JOINING INSTRUCTIONS

1-8INSTALLATION

11.Re-apply caulk or silicone as required.

12.Verify glass is positioned and operating cor- rectly.

Pivot Support

JOINING INSTRUCTIONS

Adjusting Bolt

Set Screw Positive Stop

Sectional construction means that two or more merchandisers may be joined in line yielding one long continuous display requiring only one pair of ends.

All joints must be air-tight to prevent formation of ice or condensation.

Refer to the detailed information provided in the separate Joining Instruction shipped with each case.

INSTALLING COIL COVER AND DRIP TRAY

Each gravity coil in these service merchandisers has a 4 ft (1219 mm) stainless steel coil cover and molded plastic drip tray. A condensate drip tube is factory installed.

Check the drip tray for obvious damage before installation. Damaged or leaking drip trays must be replaced. Remove any loose debris and clean the drip tray before installing.

Coil cover hooks and drip tray hooks are factory installed at the front and back in each gravity coil. Hanging holes are formed in the cover and drip tray.

Coil Cover

Drip Tube

Connection

P/N 0420057_B

U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM

Image 14

hussman P/N 0420057_B operation manual P/N 0420057B, Joining Instructions, Installing Coil Cover And Drip Tray

Contents

Installation Impact SeriesService Merchandisers Includes Wedge Installation NSF CertifiedPage INSTALLATION CONTENTSP/N 0420057B MAINTENANCECONTENTS SERVICEWARRANTY REVISION HISTORY Revision B P/N 0420057BP/N 0420057B SAFETYService Merchandisers P/N 0420057B vi CONTENTSPERSONAL SAFETY If in doubt, DO NOT ENTER and inform the clientNSF CERTIFICATION INSTALLATIONP/N 0420057B LOCATIONSHIPPING DAMAGE MERCHANDISERS SHIPPED WITH END INSTALLEDP/N 0420057B Apparent Loss or DamageP/N 0420057B Shipping Riderfor 8 ft Case Cross-MembersP/N 0420057B Leveler AdjustmentAdjustable Attention to glass position is critical during the leveling processP/N 0420057B GLASS POSITIONINGOptional Flexible Wiper Gasket ADJUSTMENT BOLTP/N 0420057B 9. The set screw and adjusting bolt are now accessible P/N 0420057BJOINING INSTRUCTIONS INSTALLING COIL COVER AND DRIP TRAYP/N 0420057B P/N 0420057B Drip Tray Connector Drip TubeInstalling Optional Wrap Board Wrapping Board Assembly for Mounting to Right Hand Side of Case 1-10 INSTALLATIONWrapping Board Assembly for Mounting to Left Hand Side of Case Wrapping Board Assembly for Mounting to Center of 12-Ft CaseP/N 0420057B 1-11Installing Optional Scale Stand 9. Reposition scale stand and attach using #8 truss head screws P/N 0420057BREFRIGERANT REFRIGERATION / ELECTRICALP/N 0420057B REFRIGERANT PIPING Connection LocationLine Sizing CONTROL SETTINGSP/N 0420057B Oil TrapsREFRIGERATION THERMOSTAT P/N 0420057BOfftime Defrost DEFROST TERMINATION THERMOSTATP/N 0420057B FIELD WIRINGIDENTIFICATION OF WIRING MERCHANDISER ELECTRICAL DATAP/N 0420057B DRIP PIPING AND SPLASHGUARDSINSTALLING DRIP PIPING WASTE OUTLET AND WATER SEALP/N 0420057B INSTALLING SPLASHGUARD AND LOWER FRONT PANELTo Install Lower Front Panel 1Leg of1Front Splashguard Retainer / Bracket 3 for 8 ft - 4 for 12 ft DetailP/N 0420057B ScrewsP/N 0420057B INSTALLING BOTTOM REAR PANELFor fixed installation 1. Align slots in bottom rear panel with center of legsDO NOT BLOCK AIR GRILLE Service MerchandisersSTART UP / OPERATION P/N 0420057BP/N 0420057B INSTALLING FDA/NSF REQUIRED THERMOMETERPlease note that the tape cannot be exposed after installation SMBTUS FDA Food Code This is an NSF-7Service Merchandisers RequiredImportant - Please read Keep with merchandiser or give to store managerDO NOT DESTROY CARE AND CLEANING MAINTENANCEduring cleaning process Turn off refrigeration, then disconnect electrical power5-2 MAINTENANCE INTERIOR CLEANING STEPSSTEP 2 - Turn off refrigeration STEP 3 - Shut power off P/N 0420057BSTEP 5 - Remove display pans STEP 6 - Lift out display pan support Service MerchandisersP/N 0420057B STEP 7 - Lift out discharge air grilleSTEP 11 - Lift out return air grille from front 5-4 MAINTENANCEP/N 0420057B Unplug fan harnessService Merchandisers STEP 14 - Clean inside the merchandiserSTEP 15 - Clean and sanitize according to Health Code requirements P/N 0420057BSTEP 16 - Reassemble in reverse order CLEANING ANTI-REFLECTIVE GLASS Anti-Reflective GlassP/N 0420057B REMOVING SCRATCHES FROM BUMPERP/N 0420057B SERVICE3. Disconnect fan from wiring harness REPLACING FAN MOTORS AND BLADESREMOVING POLYCARBONATE LAMP COVERS P/N 0420057BScrews Canopy FixtureREPLACING FLUORESCENT LAMPS ELECTRICAL SERVICE RECEPTACLESP/N 0420057B Plastic Shield Fluorescent Lamp End CapREPLACING ELECTRONIC BALLAST Lamp Ballast Behind This Panel Light Switch BelowP/N 0420057B LOCK OUT / TAG OUTP/N 0420057B to support the glass when fully open to allow the glass to come downHave your Service Contractor replace the cylinders when required REPLACING CYLINDERS SINGLE PANE GLASSSet Screw Locations P/N 0420057BREPLACING SINGLE PANE FRONT GLASS Requires more than one person Fully Engage Glass in Clamp GasketDuct Tape Glass P/N 0420057BREPLACING GLASS HAND GRIP 3/8 in. 10 mm of Duct Tape on Each Side of Bottom Edge of GlassTechnique REPAIRING ALUMINUM COILP/N 0420057B 01 July