P/N 0420057_B

3-1

DRIP PIPING AND SPLASHGUARDS

WASTE OUTLET AND WATER SEAL

The waste outlet is located in front of the fan plenum 6 ft (1829 mm) from the left-hand of the merchandiser (facing case front) allowing drip piping to be run under the fixture lengthwise.

A11/2 in. (38 mm) water seal is supplied with each fixture. The water seal must be installed to prevent air leakage and insect entrance into the fixture. A tee, adapter, ell, and plug have been shipped to allow field installation to determine direction of drain.

NOTES:

Water seal outlet must clear front skid rail. PVC–DWV solvent cement is recommended. Follow the manufacturer’s instructions.

INSTALLING DRIP PIPING

Poorly or improperly installed drip pipes can seriously interfere with the operation of these merchandisers, and result in costly maintenance and product losses. Please follow the recommen- dations listed below when installing drip pipes to ensure proper installation.

1.Never use drip piping smaller than the nominal diameter of the pipe or water seal supplied with the merchandiser.

2.When connecting drip piping, the water seal must be used as part of the drip piping to prevent air leakage or insect entrance. Never use two water seals in series in any one drip pipe. Double water seals in series will cause an air lock and prevent draining.

3.Pitch the drip piping in the direction of flow. There should be a minimum pitch of 1/8 in. per foot (3 mm per 300 mm).

4.Avoid long runs of drip piping. Long runs make it impossible to provide the pitch necessary for good drainage.

5. Provide a suitable air break between flood rim of the floor drain and outlet of drip pipe. To meet code on low base merchandisers, it may be necessary to install a field-supplied drip pipe reducer. An alternative is to cut the last section of drip pipe at an angle.

6.Prevent drip pipes from freezing:

A.Do NOT install drip pipes in contact with uninsulated suction lines. Suction lines should be insulated with a non-absorbent insulation material.

B.Where drip pipes are located in dead air spaces, such as between merchandisers or between a merchandiser and a store wall, provide means to prevent freezing.

Note: To prevent condensation problems, the water seal should be insulated.

HUSSMANN CORPORATION, Bridgeton, MO 63044-2483 U.S.A.

Service Merchandisers

Page 22 Page 24
Page 23
Image 23
hussman P/N 0420057_B operation manual Drip Piping and Splashguards, Waste Outlet and Water Seal, Installing Drip Piping
Page 22 Page 24

P/N 0420057_B specifications

The Hussman P/N 0420057_B represents a cutting-edge refrigeration solution designed for modern retail environments, particularly those requiring efficient display systems for perishable goods. As part of Hussman's extensive product lineup, this unit integrates advanced technologies tailored to enhance both performance and energy efficiency.

One of the standout features of the 0420057_B is its state-of-the-art refrigeration system, which employs a combination of environmentally friendly refrigerants and high-efficiency compressors. This design not only supports compliance with stringent environmental regulations but also contributes to reduced energy consumption, ultimately leading to lower operational costs for retailers. The unit is built to maintain consistent temperatures, ensuring that products are stored and displayed at optimal conditions, thus prolonging freshness and quality.

Another key characteristic of the Hussman P/N 0420057_B is its user-friendly interface. Retail staff can easily monitor and adjust temperature settings, ensuring that the display conditions meet specific product requirements. This feature enhances operational efficiency and minimizes the risk of temperature-related spoilage. Additionally, digital temperature controls come equipped with alarms that alert staff to any fluctuations, acting as a safeguard for perishable inventory.

The design of the unit emphasizes practicality and aesthetics. With a sleek, modern appearance, the 0420057_B fits seamlessly into various store layouts while maximizing product visibility. The glass door design allows for enhanced product presentation, attracting customers and facilitating easy access for quick purchasing decisions.

Durability is a crucial characteristic of Hussman products, and the 0420057_B is no exception. Constructed from high-quality materials, this refrigeration unit is designed to withstand the rigors of daily retail operations. The robust build ensures longevity, reducing maintenance frequency and operational downtimes, which are critical aspects for retailers aiming to enhance their profit margins.

Moreover, the Hussman P/N 0420057_B incorporates intelligent technology, such as smart sensors that optimize energy use based on real-time conditions. This capability not only enhances energy efficiency but also supports retailers in meeting sustainability goals, making this unit a valuable addition to any eco-conscious business strategy.

In conclusion, the Hussman P/N 0420057_B is a versatile refrigeration solution that combines advanced technology, user-friendly features, and sleek design to meet the demanding needs of modern retail environments. Its focus on energy efficiency, durability, and optimal product preservation makes it an essential investment for retailers looking to enhance their operational effectiveness while ensuring customer satisfaction.
Top Page Image Contents