Manuals / hussman / Kitchen Appliance / Refrigerator

hussman P/N 0420057_B P/N 0420057B, Electrical Service Receptacles, Replacing Fluorescent Lamps

Models: P/N 0420057_B

1 46

Download 46 pages 55.32 Kb

Page 39

ELECTRICAL SERVICE RECEPTACLES

P/N 0420057_B

ELECTRICAL SERVICE RECEPTACLES

The receptacles located on the exterior back of the merchandisers are intended for scales and other light duty appliances that are found in meat and delicatessen departments. The receptacles are not intended for large motors.

REPLACING FLUORESCENT LAMPS

Fluorescent lamps are furnished with moisture resistant lamp holders and end caps. Lamps on lighted shelves have plastic shields. Whenever a fluorescent lamp is replaced, be certain to re- install the plastic shields and end caps.

Plastic Shield

Fluorescent

Lamp

End Cap

!CAUTION

Fluorescent lamps contain mercury vapor. Mercury exposure at high levels can harm the brain, heart, kidneys, lungs, and immune system of people of all ages. Do not break or puncture fluorescent lamps. Dispose of, or store, all fluorescent lamps in accordance with Federal (40 CFR 273), State, and local hazardous waste requirements. Refer to http://www.epa.gov/mercury/about.htm

6-3

REPLACING LAMP HOLDERS AND END CAPS

The Hussmann Impact lamp holder is designed to snap into the sheet metal of the case. The lamp holder has a locking ‘nub’ which fits inside the groove of specially designed end caps.

Hussmann	Groove
Impact
End-Cap

Nub

Hussmann

Impact

Lamp Holder

IMPORTANT!

Always replace lamp holders and end caps with Hussmann lamp holders and end caps.

Use of non-Hussmann parts may result in poor electrical contact and short lamp life.

HUSSMANN CORPORATION, Bridgeton, MO 63044-2483 U.S.A.

Service Merchandisers

Image 39

hussman P/N 0420057_B operation manual P/N 0420057B, Electrical Service Receptacles, Replacing Fluorescent Lamps

Contents

Includes Wedge Installation NSF Certified Impact SeriesService Merchandisers InstallationPage MAINTENANCE CONTENTSP/N 0420057B INSTALLATIONP/N 0420057B SERVICEWARRANTY REVISION HISTORY Revision B CONTENTSSAFETY Service MerchandisersP/N 0420057B If in doubt, DO NOT ENTER and inform the client vi CONTENTSPERSONAL SAFETY P/N 0420057BLOCATION INSTALLATIONP/N 0420057B NSF CERTIFICATIONApparent Loss or Damage MERCHANDISERS SHIPPED WITH END INSTALLEDP/N 0420057B SHIPPING DAMAGECross-Members Shipping Riderfor 8 ft Case P/N 0420057BAttention to glass position is critical during the leveling process Leveler AdjustmentAdjustable P/N 0420057BGLASS POSITIONING P/N 0420057BADJUSTMENT BOLT P/N 0420057BOptional Flexible Wiper Gasket P/N 0420057B 9. The set screw and adjusting bolt are now accessibleINSTALLING COIL COVER AND DRIP TRAY P/N 0420057BJOINING INSTRUCTIONS Drip Tray Connector Drip Tube Installing Optional Wrap BoardP/N 0420057B Wrapping Board Assembly for Mounting to Center of 12-Ft Case 1-10 INSTALLATIONWrapping Board Assembly for Mounting to Left Hand Side of Case Wrapping Board Assembly for Mounting to Right Hand Side of Case1-11 Installing Optional Scale StandP/N 0420057B P/N 0420057B 9. Reposition scale stand and attach using #8 truss head screwsREFRIGERANT PIPING Connection Location REFRIGERATION / ELECTRICALP/N 0420057B REFRIGERANTOil Traps CONTROL SETTINGSP/N 0420057B Line SizingDEFROST TERMINATION THERMOSTAT P/N 0420057BOfftime Defrost REFRIGERATION THERMOSTATMERCHANDISER ELECTRICAL DATA FIELD WIRINGIDENTIFICATION OF WIRING P/N 0420057BWASTE OUTLET AND WATER SEAL DRIP PIPING AND SPLASHGUARDSINSTALLING DRIP PIPING P/N 0420057B1Leg of1 INSTALLING SPLASHGUARD AND LOWER FRONT PANELTo Install Lower Front Panel P/N 0420057BScrews DetailP/N 0420057B Front Splashguard Retainer / Bracket 3 for 8 ft - 4 for 12 ft1. Align slots in bottom rear panel with center of legs INSTALLING BOTTOM REAR PANELFor fixed installation P/N 0420057BP/N 0420057B Service MerchandisersSTART UP / OPERATION DO NOT BLOCK AIR GRILLESMBT INSTALLING FDA/NSF REQUIRED THERMOMETERPlease note that the tape cannot be exposed after installation P/N 0420057BRequired This is an NSF-7Service Merchandisers US FDA Food CodeKeep with merchandiser or give to store manager DO NOT DESTROYImportant - Please read Turn off refrigeration, then disconnect electrical power MAINTENANCEduring cleaning process CARE AND CLEANINGP/N 0420057B INTERIOR CLEANING STEPSSTEP 2 - Turn off refrigeration STEP 3 - Shut power off 5-2 MAINTENANCESTEP 7 - Lift out discharge air grille Service MerchandisersP/N 0420057B STEP 5 - Remove display pans STEP 6 - Lift out display pan supportUnplug fan harness 5-4 MAINTENANCEP/N 0420057B STEP 11 - Lift out return air grille from frontP/N 0420057B STEP 14 - Clean inside the merchandiserSTEP 15 - Clean and sanitize according to Health Code requirements Service MerchandisersREMOVING SCRATCHES FROM BUMPER CLEANING ANTI-REFLECTIVE GLASS Anti-Reflective GlassP/N 0420057B STEP 16 - Reassemble in reverse orderREPLACING FAN MOTORS AND BLADES SERVICE3. Disconnect fan from wiring harness P/N 0420057BCanopy Fixture P/N 0420057BScrews REMOVING POLYCARBONATE LAMP COVERSPlastic Shield Fluorescent Lamp End Cap ELECTRICAL SERVICE RECEPTACLESP/N 0420057B REPLACING FLUORESCENT LAMPSLOCK OUT / TAG OUT Behind This Panel Light Switch BelowP/N 0420057B REPLACING ELECTRONIC BALLAST Lamp BallastREPLACING CYLINDERS SINGLE PANE GLASS to support the glass when fully open to allow the glass to come downHave your Service Contractor replace the cylinders when required P/N 0420057BFully Engage Glass in Clamp Gasket P/N 0420057BREPLACING SINGLE PANE FRONT GLASS Requires more than one person Set Screw Locations3/8 in. 10 mm of Duct Tape on Each Side of Bottom Edge of Glass P/N 0420057BREPLACING GLASS HAND GRIP Duct Tape GlassREPAIRING ALUMINUM COIL P/N 0420057BTechnique 01 July