Manuals / hussman / Kitchen Appliance / Refrigerator

hussman P/N 0420057_B P/N 0420057B, Installing Splashguard And Lower Front Panel, 1Leg of1, Case

Models: P/N 0420057_B

1 46

Download 46 pages 55.32 Kb

Page 24

INSTALLING SPLASHGUARD AND LOWER FRONT PANEL

3-2DRIP PIPING AND SPLASHGUARDS

INSTALLING SPLASHGUARD AND LOWER FRONT PANEL

Make certain that the end assemblies, end splashguards and end panels have been installed according to the End Kit instruction.

The splashguard and lower front panel are shipped inside each case. After merchandisers have been leveled and joined, and all drip piping, electrical and refrigeration work has been completed, install the splashguard and lower front panel.

1.At front of merchandiser, attach a splashguard retainer/bracket to each leg with sheet metal screws.

2.Position top of splashguard over the top edge of the retainer/bracket as shown below.

3.Push the lower edge of the splashguard toward the bottom of the bracket until it snaps into place.

To Install Lower Front Panel

1.Position the lower front panel with the top angled as shown in the illustration. Tabs extending from the upper front assembly are designed to fit into the slots on the top of the lower front panel.

2.Once the top is positioned, lift the panel up and drop it into the groove at the top of the splashguard.

Do not use additional fasteners or sealant to hold splashguards or panels in place. To meet NSF cleanability requirements, splashguards and panels must be removable without tools.

1Leg of1

Case	Tab

Retainer/

Bracket

	Lower	Leg of
	Front
		Case
	Panel

2

Leg of

Case

Splashguard

	2	Lower Front Panel
	Leg of	Leg of
3	Case	Case
Splashguard

P/N 0420057_B

U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM

Image 24

hussman P/N 0420057_B P/N 0420057B, Installing Splashguard And Lower Front Panel, To Install Lower Front Panel, 1Leg of1

Contents

Impact Series Service MerchandisersInstallation Includes Wedge Installation NSF CertifiedPage CONTENTS P/N 0420057BINSTALLATION MAINTENANCESERVICE WARRANTY REVISION HISTORY Revision BCONTENTS P/N 0420057BSAFETY Service MerchandisersP/N 0420057B vi CONTENTS PERSONAL SAFETYP/N 0420057B If in doubt, DO NOT ENTER and inform the clientINSTALLATION P/N 0420057BNSF CERTIFICATION LOCATIONMERCHANDISERS SHIPPED WITH END INSTALLED P/N 0420057BSHIPPING DAMAGE Apparent Loss or DamageShipping Rider for 8 ft CaseP/N 0420057B Cross-MembersLeveler Adjustment AdjustableP/N 0420057B Attention to glass position is critical during the leveling processP/N 0420057B GLASS POSITIONINGADJUSTMENT BOLT P/N 0420057BOptional Flexible Wiper Gasket 9. The set screw and adjusting bolt are now accessible P/N 0420057BINSTALLING COIL COVER AND DRIP TRAY P/N 0420057BJOINING INSTRUCTIONS Drip Tray Connector Drip Tube Installing Optional Wrap BoardP/N 0420057B 1-10 INSTALLATION Wrapping Board Assembly for Mounting to Left Hand Side of CaseWrapping Board Assembly for Mounting to Right Hand Side of Case Wrapping Board Assembly for Mounting to Center of 12-Ft Case1-11 Installing Optional Scale StandP/N 0420057B 9. Reposition scale stand and attach using #8 truss head screws P/N 0420057BREFRIGERATION / ELECTRICAL P/N 0420057BREFRIGERANT REFRIGERANT PIPING Connection LocationCONTROL SETTINGS P/N 0420057BLine Sizing Oil TrapsP/N 0420057B Offtime DefrostREFRIGERATION THERMOSTAT DEFROST TERMINATION THERMOSTATFIELD WIRING IDENTIFICATION OF WIRINGP/N 0420057B MERCHANDISER ELECTRICAL DATADRIP PIPING AND SPLASHGUARDS INSTALLING DRIP PIPINGP/N 0420057B WASTE OUTLET AND WATER SEALINSTALLING SPLASHGUARD AND LOWER FRONT PANEL To Install Lower Front PanelP/N 0420057B 1Leg of1Detail P/N 0420057BFront Splashguard Retainer / Bracket 3 for 8 ft - 4 for 12 ft ScrewsINSTALLING BOTTOM REAR PANEL For fixed installationP/N 0420057B 1. Align slots in bottom rear panel with center of legsService Merchandisers START UP / OPERATIONDO NOT BLOCK AIR GRILLE P/N 0420057BINSTALLING FDA/NSF REQUIRED THERMOMETER Please note that the tape cannot be exposed after installationP/N 0420057B SMBTThis is an NSF-7 Service MerchandisersUS FDA Food Code RequiredKeep with merchandiser or give to store manager DO NOT DESTROYImportant - Please read MAINTENANCE during cleaning processCARE AND CLEANING Turn off refrigeration, then disconnect electrical powerINTERIOR CLEANING STEPS STEP 2 - Turn off refrigeration STEP 3 - Shut power off5-2 MAINTENANCE P/N 0420057BService Merchandisers P/N 0420057BSTEP 5 - Remove display pans STEP 6 - Lift out display pan support STEP 7 - Lift out discharge air grille5-4 MAINTENANCE P/N 0420057BSTEP 11 - Lift out return air grille from front Unplug fan harnessSTEP 14 - Clean inside the merchandiser STEP 15 - Clean and sanitize according to Health Code requirementsService Merchandisers P/N 0420057BCLEANING ANTI-REFLECTIVE GLASS Anti-Reflective Glass P/N 0420057BSTEP 16 - Reassemble in reverse order REMOVING SCRATCHES FROM BUMPERSERVICE 3. Disconnect fan from wiring harnessP/N 0420057B REPLACING FAN MOTORS AND BLADESP/N 0420057B ScrewsREMOVING POLYCARBONATE LAMP COVERS Canopy FixtureELECTRICAL SERVICE RECEPTACLES P/N 0420057BREPLACING FLUORESCENT LAMPS Plastic Shield Fluorescent Lamp End CapBehind This Panel Light Switch Below P/N 0420057BREPLACING ELECTRONIC BALLAST Lamp Ballast LOCK OUT / TAG OUTto support the glass when fully open to allow the glass to come down Have your Service Contractor replace the cylinders when requiredP/N 0420057B REPLACING CYLINDERS SINGLE PANE GLASSP/N 0420057B REPLACING SINGLE PANE FRONT GLASS Requires more than one personSet Screw Locations Fully Engage Glass in Clamp GasketP/N 0420057B REPLACING GLASS HAND GRIPDuct Tape Glass 3/8 in. 10 mm of Duct Tape on Each Side of Bottom Edge of GlassREPAIRING ALUMINUM COIL P/N 0420057BTechnique 01 July