Reset
button
Indicator
Figure
Incorrect air cleaner element
Use only the correct Donaldson air filter element, Hustler part number 785261, which is designed to fit the canister properly.
Hustler air filter elements have the correct media composition, filter area, micron size and dimensions. Always use genuine Hustler filters. Many aftermarket filters have been found to be incompatible with Hustler’s canisters and engines.
Viewed from
bottom for unit
1.Pump belt
2.Engine pulley
3.Pump idler pulley
4.Pump idler arm
5.Pump pulley
6. | Electric deck clutch | 1 |
7. | Pump idler spring |
|
5
5
4
7 | 2, 6 |
3
Figure
The air filter must remain intact to block passage of dirt and foreign particles from entering the engine. Being inclined to disbelieve the need for more expensive air filter elements used on gasoline engines may cause some individuals to opt for a less expensive part.
The filter element must be sufficient size and construction to withstand stresses, caused by rapid cycling of the air volume demanded by the engine, without cracking or tearing under fatigue and pressure (especially diesel engines). Therefore, Hustler Turf Equipment and the engine manufacturers have carefully selected a reliable filter designed to fit the needs of the engines. The filter specified is a Donaldson filter, Hustler part number 785261.
Owners should be reminded that failure to use original equipment replacement parts is an “alteration” and will not be considered for warranty in the event of engine damage.
Recommended service procedure
1. | Release clamps and remove element. Clean the canister with a damp |
2. | cloth. |
Before installing a new element, inspect it by placing a bright light | |
| inside and rotate the element slowly, looking for any holes or tears in |
| the paper. Also check gaskets for cuts or tears. Do not attempt to |
| use a damaged element which will allow abrasive particles to enter |
3. | the engine. |
Reinstall the dust cup. Make sure it seals all the way around the air | |
4. | cleaner body, then tighten the clamps. |
Check all fittings and clamps periodically for tightness and inspect |
2
5
2 
3 6
1
2
5
4
Deck Belt Drive Layout
1.Spindle drive belt
2.Deck blade spindle pulley
3.Spindle belt tension idler
4.Spindle belt tension idler spring (7.75" at operation)
5.Deck belt idler
6.Idler arm
5. | hoses for holes or cracks. |
Periodically check the intake hose for signs of ingested dust. Locate | |
6. | and repair the source of ingested dirt. |
Never operate a machine without an air filter installed. |
Air restriction indicator
Any unit with a Kawasaki engine will have an air restriction indicator installed in the air cleaner. Fig.
Replace the element whenever the restriction indicator shows reaches the change filter red line. Check the indicator daily and replace element as needed or annually whichever occurs first.
Reset the indicator by pushing in on the yellow button after each element change. Fig,
A restriction indicator takes the guesswork out of air cleaner servicing and allows you to safely benefit from the filter’s optimum performance.
General engine maintenance
Detailed instructions and recommendations for
Figure
maintenance are specified in the Engine Owner’s manual. Please refer to this manual for engine servicing, lubricating oil levels with quality and viscosity recommendations, bolt torques, etc. The engine warranty is backed by the manufacturer. Special attention should be paid to applicable data which will not be duplicated here.
Belt replacement
Figures 11-14 and 11-15 show diagrams and descriptions of the unit’s belt drive systems.
Inspect these belts frequently for wear and serviceability. Replace a belt that shows signs of severe cuts, tears, separation, weather checking and cracking, or burns caused by slipping. Slight raveling of belt covering does not indicate failure, trim ravelings with a sharp knife.
WARNING: If the pump belt fails, loss of control will occur especially when operating on a slope. If you lose steering control while operating the machine, place the steering
302620 8/06 |
|
