Manuals / Icom / Marine Equipment / Marine Radio

Icom IC-V8 instruction manual Optional HM-75A required

Models: IC-V8

1 68

Download 68 pages 36.59 Kb

Page 62

11 OTHER FUNCTIONS

D Mic simple mode	Optional HM-75A required

This item turns the microphone simple mode ON and OFF. Microphone simple mode is used to change the function assignments for keys in the optional HM-75A REMOTE CONTROL SPEAKER-MICROPHONEas below. This assign- ment is convenient for 3-channel use of sim- ple operation.

•mIC.N1 : Normal 1 (default)

•mIC.N2 : Normal 2

•mIC.Sm : Simple mode

FTX

MR

FTX

MR

	HM-75A	Mode	NORMAL1	NORMAL2	SIMPLE
	key	Mode	NORMAL1	NORMAL2	SIMPLE
	key

	[A]	Freq.	[B•CALL]	[SQL]	[SQL]
	[A]	CH	Null	[SQL]	[SQL]
		CH	Null

	[B]	Freq.	VFO/Memory	VFO/Memory	[B•CALL]
	[B]	CH	Null	Null	[B•CALL]
		CH	Null	Null

	[∫]	Freq.	Freq. Up	Freq. Up	MR-00CH
	[∫]	CH	Memory CH Up	Memory CH Up	MR-00CH
		CH	Memory CH Up	Memory CH Up

	[√]	Freq.	Freq. Down	Freq. Down	MR-01CH
	[√]	CH	Memory CH Down	Memory CH Down	MR-01CH
		CH	Memory CH Down	Memory CH Down

NOTE:

Turn power OFF when connecting the HM-75A to the trans-

ceiver.

VFO mode cannot be selected via the microphone when SIM- PLE mode is selected.

53

Image 62

Icom IC-V8 instruction manual Optional HM-75A required

Contents

IV8 Safety Training Information Page Foreword Supplied Accessories Precaution For USA only Table of Contents Dtmf Memory Cloning 13 Optional Unit 14 Specifications 15 OptionsMemory Programming Scan OperationPTT Switch PTT ‘ Switches, controls, keys and connectorsPower Switch Power MicrophoUP/DOWN Keys Y/Z Squelch Switch SQLAntenna Connector SP/MIC JackKey pad KEY FunctionPanel Description Key pad Panel Description ‘ Function display Signal Indicator 0LOW Power IndicatorBelt clip ‘ Accessory attachmentAntenna ‘ Battery pack replacement Battery Packs‘ Battery caution Recycling information U.S.A. onlyWith the BC-146 ‘ Battery chargingDRegular charging About AD-99Rapid charging with the BC-144 Rapid charging with the BC-121+AD-94 #11Battery pack life ‘ Charging Note‘ Battery case optional for some versions Via the keypad Power onSetting a frequency To set the audio level Setting audio/squelch levelBy other methods To set the squelch levelReceive and transmit Key lock function Selecting a memory channelSelecting call channel Using Initial SET Mode Display typeAbout reversed duplex mode GeneralUsing SET Mode Offset frequencyTone information Hz ToneFrequency Range Duplex Direction Memory channel contents Programming the memory/call ChannelsMemory/call VFO Channel name programmingMemory transferring Clearing a memory Memory/call call/memoryProgramming a Dtmf code One of d0 to d4 appearsTransmission speed Using a Dtmf memory channelTransmitting a Dtmf code Manual Dtmf code transmissionPriority memory channel scan Scan typesPriority memory channel watch Programmed scan Setting skip channels Memory skip scanMemory scan watch Priority watchMemory or call channel watch Scan resume Condition Operation Recommended tone frequenciesSetting subaudible tones for tone squelch operation Available Ctcss tone frequency list‘ Pocket beep operation Waiting for a call from a speciﬁc station‘ Tone scan PAGER/CODE Squelch Before programming Code channel assignmentCode programming Receive accept/receive inhibit Pager/code squelch operation during channel indicationCalling a speciﬁc station Waiting for call from a speciﬁc station Personal Calls‘ Code squelch Tone squelch frequency Entering set modeRepeater tone frequency Dtcs codeFunction key timer Tuning stepScan pause timer LCD backlightTransmission permission Pager/Code squelch channel Optional UT-108 requiredKey-touch beep Entering initial set modeTime-out timer DAuto power-off Repeater lock-outDial assignment Squelch delayDtmf speed Display typeLCD contrast Power saveTuning speed acceleration Optional HM-75A required ‘ CPU reset DTransceiver-to-transceiver cloning AT Power on Cloning using a PCOptional UT-108 installation Optional UnitSpecifications Options Count on us